Lanex XPTH-020 Instruction Manual

personal protective equipment must be withdrawn from use immediately and destroyed when it have been used to arrest a fall.
a full body harness is the only acceptable body holding device that can be used in a fall arrest system.
the anchor device or anchor point for the fall arrest system should always be positioned, and the work carried out in such a way, as to minimise both the potential for falls and
potential fall distance. The anchor device/point should be placed above the position of the user . The shape and construction of the anchor device/point shall not allowed to
self-acting disconnection of the equipment. Minimal static strength of the anchor device/point is 15 kN. It is recommended to use certified and marked structural anchor point
complied with EN795.
it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest system, so that, in the case of a fall, there will be
no collision with the ground or other obstacle in the fall path. The required value of the free space should be taken from instruction manual of used equipment.
there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization,
especially:
- trailing or looping of lanyards or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of steel or plastic) to protect it against
damage or moisture.
the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use mild detergents for delicate
fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. When the equipment becomes wet, either from being in use or when
due cleaning, it shall be allowed to dry naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly
slightly lubricated to ensure better operation.
The site where the equipment is used is responsible for completing the utilisation card.
The utilisation card should be filled in before the first release for use of the device.
All the information pertaining to the protective equipment (name, serial number, date of purchase and date of introduction into
use, user name, information about periodic surveys and repairs) should be included in the utilisation card of a device.
The card is filled in by the person in charge of protective equipment on site.
Pieces of personal protective equipment without a complete utilisation card must not be used.

USER CARD

DEVICE NAME
MODEL
NUMBER OF DEVICE
USER NAME
DATE OF PURCHASE
TECHNICAL SURVEYS
SURVEY DATE REASONS FOR SURVEY OR REPAIR
1
2
3
4
5
EC type examination carried out by CETE APAVE SUDEUROPE, BP 193, 13322 Marseille, France - 0082
LANEX a. s. - Hluèínská 1 / 96, 747 23 Bolatice, Tel: + 420 553 751 111, Fax:: + 420 553 654 125, E-mail: lanex@lanex.cz, www.lanex.cz
,
CATALOGUE NO.
DATE OF MANUFACTURE
DATE OF INTRODUCTION INTO USE
DAMAGES FOUND, REPAIRS PERFORMED, DATE OF NEXT SURVEY
OTHER NOTES
Instruction Manual
Ref.: TH 120 01
Ref.: TH 130 01
EN 358:1999 EN 813:2008
Work positioning belt XPTH-020 or XPTH-030 is a component of the personal protective equipment for work positioning and prevention of
falls from a height. It can be used also as a sit harness. The belt complies with EN 358 (work positioning belt) and EN 813 (sit harness).
It is strictly forbidden to use work positioning belt XPTH-020 and XPTH-030 in fall arrest system as a full body harness.
Only a full body harness complied with EN 361 is the only acceptable body holding device that can be used in a fall arrest system.
According EN 358 - work positioning lanyard must be anchored to the point of construction that is situated at waist level or above.
Work positioning lanyard must be kept taut to restrict free movement to a maximum 0,5 m.
All textile components of sit harness XPTH-020 and XPTH-030 are made from polyamide/polyester, yarns and fabrics, the metal parts are
made from light alloy. Inside the pads is polyethylene foam.

BASIC EQUIPMENT

1. Front attaching ring - can be utilized as a sit harness
according EN 813.
2. Attaching strap.
3. Lateral belt attaching D-rings. Can be utilized only to attach work
positioning systems according EN 358.
4. Belt strap.
5. Belt strap adjusting buckles.
6. Thigh straps.
7. Thigh straps connecting/adjusting buckles.
8. Identity label - on back thigh pad
9. Belt pad.
10. Tool loop - for attaching tools and tool bags.
11. Connecting shackle

SIZES

Belt XPTH-020 and XPTH-030 is manufactured in three sizes:
1. small - S; 2. universal - M-XL; 3 extra large -XXL

Maximum lifetime of the device

The maximum lifetime of the device is 8 years from the date of manufacture. The maximum lifetime depends on the intensity of usage and the
environment of usage. Using the device in rough environment, marine environment, contact with sharp edges, exposure to extreme temperatures or
agressive substances, etc. can lead to the wthdrawal from use even after one use.
The device must be withdrawn from use immediately and destroyed when it has been used to arrest a fall.
BELT MARKING
a. Device type.
b. Model symbol.
c. Reference number.
d. European standards (number and year)
e. CE mark and identity number
of the authorized body for article 11A
f. Month and year of manufacture.
g. Serial number of the belt.
h. Belt size.
i. Caution: read the manual
SIGNATURE OF j. Marking of the manufacturer or distributor of the belt
PERSON
RESPONSIBLE
Fasten the thigh and belt buckles,
adjust the length of the straps.
Model XPTH-020
Work Positioning Belt
XPTH-020 XPTH-030
9
3
5
4
1
2
7
6
10
XPTH-020MXL
M-XL
b Size:
WORK POSITIONING BELT
Serial number:
Ref.: XPTH-020
0000000
EN 358:1999
EN 813:2008
Max. load 100 kg
Date of manufacture:
09.2010
a
c
g
b i d f h
XPTH-030MXL
M-XL
e Size:
WORK POSITIONING BELT
Serial number:
Ref.: XPTH-030
0000000
EN 358:1999
EN 813:2008
Max. load 100 kg
Date of manufacture:
09.2010
i
Model XPTH-030
11
j