DMP Electronics X1 Series Installation And Programming Manual
Elevator controller
Hide thumbs
Also See for X1 Series:
- Installation and programming manual (24 pages) ,
- Compliance manual (6 pages) ,
- Installation and programming manual (9 pages)
Related Manuals for DMP Electronics X1 Series
Summary of Contents for DMP Electronics X1 Series
- Page 1 X1 SERIES ELEVATOR CONTROLLER INSTALLATION AND PROGRAMMING GUIDE LT-2463 1.01 21293 © 2021...
-
Page 2: Table Of Contents
TABLE OF CONTENTS X1 Series Elevator Controller Overview ���������� 1 Step 7: Manage Connection Settings ��������� 10 Elevator Controller Configurations �����������������������1 Configure Wi-Fi Settings����������������������������������������10 Elevator Controller Power ����������������������������������������1 Configure Network Settings ���������������������������������10 Elevator Controller Plug-In Terminals ������������������1 Configure Cell Settings �������������������������������������������10 Elevator Controller PCB Components ����������������2... -
Page 3: X1 Series Elevator Controller Overview
X1 SERIES ELEVATOR CONTROLLER OVERVIEW The X1 Series is a cloud-based access elevator controller that is fully programmed in Dealer Admin™ and maintained in Virtual Keypad™� One X1 Elevator Controller can have up to 90 floors on a total of nine elevator control modules�... -
Page 4: Elevator Controller Pcb Components
Top 4-Wire Connector DATA Floor Relays RELAY Floor Relay LEDs NC 6 NO NC 7 NO NC 8 NO NC 9 NO NC 10 NO RELAY RELAY RELAY RELAY RELAY X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 5: Pre-Installation
STEP 1: MOUNT THE ELEVATOR CONTROLLER X1 Elevator Controller The metal enclosure for the X1 Series Elevator Controller must be mounted directly to a wall, backboard, or other flat surface in a secure, dry place to protect the elevator controller from damage� It is not necessary to remove the PCBs when installing the enclosure�... -
Page 6: Optional X1 Elevator Controller Pcb Only
X1 Elevator Controller Second X1 Elevator Module Third X1 Elevator Module First X1 Elevator Module X1 Elevator Expansion 12 V Battery X1 Elevator Controller X1 Elevator Expansion X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 7: Step 2: Connect A Card Reader
For an Out Reader, connect the red, white, green, and black wires to the Reader 2 terminals: R2, W2, G2, and B2� Connect the orange/brown wire to LC� If using only one reader, it must be connected to reader 1� X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 8: Step 3: Wire For Floor Access
STEP 3: WIRE FOR FLOOR ACCESS The X1 Series Elevator Control Module provides 10 Form C (SPDT) 1 Amp relays for controlling access to 10 floors� The three relay terminals are labeled for normally open (NO) and normally closed (NC) operation� The center terminal is the common�... -
Page 9: Step 4: Wire Optional Inputs And Outputs
The relay contacts must be connected to devices located within 98�5 ft (30m) of the X1� 12V+ (12V) Attach the positive wire of the device here� 02 12V +AC/DC- +BAT- R2 W2 G2 DS RX X1 Elevator Controller X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 10: Step 5: Determine Communication
The yellow Wi-Fi antenna connects to the right of the cell antenna on the enclosure� If the cable has become detached from the X1, simply plug it back onto the Wi-Fi module and run the cable around the module� X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 11: Step 6: Apply Power
NC 4 NO NC 5 NO DATA = wire polarity or terminal location NC 6 NO NC 7 NO NC 8 NO NC 9 NO NC 10 NO X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 12: Step 7: Manage Connection Settings
4� Select Apply, and the elevator controller will reset� Configure Cell Settings On power up, if using cell, the elevator controller automatically connects and programming in Dealer Admin can begin� X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 13: Step 8: Program In Dealer Admin
STEP 8: PROGRAM IN DEALER ADMIN After you’ve installed the X1 Series Elevator Controller and configured basic communication settings, follow the steps in each of the following sections to program an elevator controller in Dealer Admin: 1� Sign In to Dealer Admin 2�... -
Page 14: Program The X1 Elevator Controller
Under Floors, select the Add icon � 2� Enter the name and address of the elevator control module� 3� Name up to 10 floor relays� 4� Press Save� X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 15: Add Card Formats
Note: If you receive a message that states the email is already in use, the user already has a Virtual Keypad account� Select Existing below the user’s email address� X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 16: Step 9: Test The Elevator Controller
The elevator control modules each have ten onboard LEDs per floor relay� For visual confirmation of the relay operation, the LEDs are on when the relay is on and off when the relay is off� X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... -
Page 17: Additional Information
LEDs will turn off� The Power LED will turn on steady to indicate the factory default DS RX is complete� PWR/BOOT READER 1 READER 2 RELAY L Terminal DATA FIRE LOCKDOWN 4-Wire Operation Connector LEDs X1 SERIES ELEVATOR CONTROLLER INSTALLATION & PROGRAMMING GUIDE | DIGITAL MONITORING PRODUCTS... - Page 18 Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public. X1 SERIES ELEVATOR X1 Elevator Module Specifications Module Current Draw 20 mA...
Need help?
Do you have a question about the X1 Series and is the answer not in the manual?
Questions and answers