Additional Specific Safety Rules - Stanley SJ45 Manual

ENGLISH
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/
or remove the battery pack, if detachable from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc., in accordance with these instructions taking
into account the working conditions and the
work tobe performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

Safety Instructions for Jigsaw
a. Hold power tools by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the opertator an electric shock.
b. Use clamps or another practical way to secure
and support the work piece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
c. Keep hands away from cutting area.Never reach
underneath the material for any reason. Hold front
of saw by grasping the contoured gripping area. Do
not insert fingers or thumb into the vicinity of the
reciprocating blade and blade clamp. Do not stabilize
the saw by gripping the shoe.
6
d. Keep blades sharp. Dull blades may cause the saw to
swerve or stall under pressure.
e. When cutting pipe or conduit ensure that they are
free from water, electrical wiring, etc.
f. Allow the motor to come to a complete stop before
withdrawing the blade from the kerf (the slot
created by cutting). A moving blade may impact the
workpiece causing a broken blade, workpiece damage
or loss of control and possible personal injury.
g. Do not touch the workpiece or the blade
immediately after operating the tool. They can
become very hot.
h. Keep handles dry, clean, free from oil and grease.
This will enable better control of the tool.
i. Clean out your tool often, especially after heavy
use. Dust and grit containing metal particles often
accumulate on interior surfaces and could create an
electric shock hazard.
j. Do not operate this tool for long periods of time.
Vibration caused by the operating action of this tool
may cause permanent injury to fingers, hands, and
arms. Use gloves to provide extra cushion, take
frequent rest periods, and limit daily time of use.
k. Avoid prolonged contact with dust from sawing
activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust
to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
l. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
m. Don not cut oversize workpiece.
n. Make sure the blade is not contacting the
workpiece before the switch in turned on.
p. Do not leave the tool running. Operate the tool only
when hand held.
q. Some material contains chemicals witch may be
toxic. Take caution to prevent dust inhalation and skin
contact. Follow material supplier safety data.
r. Always switch off and wait for the blade to come
to complete stop before removing the blade from the
workpiece.
Additional Safety Information
WARNING: We recommend the use of a residual
current device with a residual current rating of
30mA or less.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.