Advertisement
Quick Links
Advertisement
Related Manuals for Canon D1
-
Booklet makers Canon Trimmer-A1 Operation Manual
Canon two-knife booklet trimmer-a1 (35 pages)
-
Booklet makers Canon BLM 550+ Service Support Manual
(30 pages)
-
Booklet makers Canon Oce BLM550+ Operation Manual
(138 pages)
-
Booklet makers Canon Smart Dedicated Design BLM300C Service Support Manual
Professional booklet maker (36 pages)
Summary of Contents for Canon D1
- Page 2 Structure of the Users Guide Chapter 1 Before You Begin Operating Procedures Chapter 2 Chapter 3 Troubleshooting Chapter 4 Appendix Read here first.
-
Page 4: Important Information
• Canon pursues a policy of continuing improvement in design and performance of the product. Therefore, the product design and specifications are subject to change without prior notice and without legal obligation. -
Page 5: Safe Use Of Machine
Safe Use of Machine To use this machine safely, proper operation and periodical maintenance are indispensable. Read the safety precautions described in this manual thoroughly, and do not perform operations or maintenance procedures until you understand them completely. The operating procedures and safety precautions described in this manual are valid only for proper use of this machine. -
Page 6: Caution Label Locations
Caution Label Locations FCC NOTICES This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter- ference when the equipment is operated in a commercial environment. -
Page 7: Table Of Contents
[3] Booklet Lifter Section 1 ... 1-5 [4] Booklet Lifter Section 2 ... 1-6 [5] Conveyor Section ... 1-7 Section 2 Operating Procedures Trimmer Setup ... 2-2 Operation While Trimming ... 2-3 Section 3 Troubleshooting Error Messages ... 3-2 Service Call Error ... 3-2 Error Message Chart ... -
Page 8: Before You Begin
Before You Begin Machine Description ... 1-2 Section Descriptions ... 1-3 [1] Infeed Section ... 1-3 [2] Trim Section... 1-4 [3] Booklet Lifter Section 1 ... 1-5 [4] Booklet Lifter Section 2 ... 1-6 [5] Conveyor Section... 1-7 CHAPTER... -
Page 9: Machine Description
Machine Description [1] Infeed Section (See page 1-3.) [2] Trim Section (See page 1-4.) [3] Booklet Lifter Section 1 (See page 1-5.) [4] Booklet Lifter Section 2 (See page 1-6.) [5] Front Cover [6] Conveyor Section (See page 1-7.) Machine Description... -
Page 10: Section Descriptions
Once the trimmer is installed, you cannot touch this section. When booklet jams in this section, pull out the trim unit and remove the jammed booklet from the space on the trim unit (See page 1-4.). -
Page 11: Trim Section
These belts move the booklets. Handle [TC2] Hold this green handle and pull out the trim unit. Trimmer Booklet Waste Tray Trim is collected in this tray. When it is full, the host machine displays an error message. If trim drops off inside... -
Page 12: Booklet Lifter Section 1
[3] Booklet Lifter Section 1 This section lifts each booklet and delivers. Locking Lever Booklet Lifter Section Belt Unit [TB] If a booklets jam in the booklet lifter section, hold the green lock- ing lever and open this mecha- nism to remove the jammed booklets. -
Page 13: Booklet Lifter Section 2
[4] Booklet Lifter Section 2 This section delivers each booklet to the conveyor. Delivery Section Cover If a booklets jam in the delivery section, open this cover and remove the jammed booklets. Transport Belts These belts move the booklets. Section Descriptions Delivery Section Transport Belt Unit [TA] If a booklets jam in the delivery section, hold the han- dle with green label and open this mechanism to... -
Page 14: Conveyor Section
[5] Conveyor Section The booklets delivered from the booklet lifter section are laid out on the conveyor. Delivery Tray This tray holds the stacked booklets. It is removable. (When the tray is removed, the conveyor full is not detected, and the continuous operation is possible.) Removing the delivery tray. - Page 15 Section Descriptions...
-
Page 16: Operating Procedures
Operating Procedures CHAPTER Trimmer Setup ... 2-2 Operation While Trimming ... 2-3... -
Page 17: Trimmer Setup
Turn on the power switch on the saddle stitcher first, then turn on the power switch on the host machine (printer). Trimmer will also be powered on because it is connected to the saddle stitcher. See the operation manual for the printer and set up the printer. -
Page 18: Operation While Trimming
If trim drops off inside the machine when this tray is pulled out, make sure to remove the dropped trim. To reposition the trimmer booklet waste tray, insert until it reaches to the rear end. Close the front cover, and the operation restarts automatically. - Page 19 If a booklets jam, open the cover or mechanism shown below to remove the jammed booklets. Delivery Section Cover Transport Belt Unit Front Cover Trim Unit CAUTION When removing jammed booklets from the trim sec- tion, take care not to touch the blade edge.
-
Page 20: Troubleshooting
Troubleshooting This section describes the cause and solution of the errors. Error Messages... 3-2 Service Call Error... 3-2 Error Message Chart... 3-3 Clearing Paper Jams ... 3-4 CHAPTER... -
Page 21: Error Messages
If the SERVICE CALL ERROR is still shown on the LCD of the host machine, check the following items, turn off the main power, and disconnect the power plug of the booklet trim- mer-D1. Then contact your local authorized dealer. - Product Name... -
Page 22: Error Message Chart
Lift the E handle and remove the booklets from the con- veyor. Open the front cover waste tray , and empty it. Reposition the trimmer book- let waste tray and close the front cover D sec- Open the front cover from the space on the trim unit. -
Page 23: Clearing Paper Jams
Clearing Paper Jams Jam in Conveyor Section • Paper chip jams. (See proce- dure 1.) • Transport belts are dirty. (See procedure 2.) Jam in Trim Section • Paper chip jams. (See pro- cedure 1.) • Transport belts are dirty. (See procedure 2.) Procedure 1 Open the guide and check to see if there are any paper chips left on the booklet feed path. -
Page 24: Appendix
Appendix CHAPTER Specifications ... 4-2 Index ... 4-3... -
Page 25: Specifications
When the delivery tray is removed, the conveyor full condition is not detected, and the continuous opera- tion is possible. Specifications Booklet Trimmer-D1 Upper knife reciprocating fore-edge trimmer with delivery tray 50 sheets (80 gsm), 48 sheets (80 gsm) + 2 sheets (300 gsm) A3, B4, A4R, 13"... -
Page 26: Index
Transport Hooks ... 1-3 Trim Section ... 1-2, 1-4 Trim Section Entrance Transport Belt Unit ... 1-4 Trim Section Transport Belt Unit ... 1-4 Trim Unit ... 2-4 Trimmer Booklet Waste Tray ... 1-4, 2-3 Trimmer Setup ... 2-2 Index... - Page 27 Index...
- Page 28 CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROPA N.V. Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands (See http://www.canon-europe.com/ for details on your regional dealer)