Related Manuals for Argos JENSON 891/7944
Summary of Contents for Argos JENSON 891/7944
- Page 1 JENSON Gloss 891/7944 889/2416 Spare Parts Customer Support Visit: www.argos-support.co.uk Call: 0345 640 2020 Email: Help@ClickSpares.co.uk Call: 0330 016 1114 Issue 2 - 28/01/21...
- Page 2 Safety Important - Please read these instructions fully before starting assembly • WARNING: To prevent • Warning: This unit weighs possible overbalancing this unit approximately 50kgs. must be secured to a wall using Please lift with care. the 2 overbalance protector kits •...
- Page 3 Cabinet Panels Please do NOT remove any protective film until after assembly 42.3 x 42.9cm 42.3 x 42.9cm 42.3 x 41.5cm 58.3 x 41.4cm 58.3 x 6.0cm 42.3 x 41.5cm 57.2 x 41.4cm 57.2 x 6.0cm 1779.0 x 36.5cm 180.2 x 45.0cm 58.3 x 39.6cm 57.2 x 39.6cm 59.6 x 32.7cm...
- Page 4 Fittings Use these drawings to correctly identify the fittings Bag 1 x 32 x 16 x 16 x 12 x 16 Tools Only used for drilling walls...
- Page 5 Finished front edges...
- Page 6 Finished front edge Finished front edge...
- Page 7 Finished front edge Finished front edge...
- Page 8 Finished front edge...
- Page 9 Finished front edge...
- Page 10 Finished front edge Finished front edge...
- Page 12 Finished front edge...
- Page 13 Finished front edge Finished front edge...
- Page 15 Finished front edge...
- Page 16 Squaring up a Chest and fitting the Back Panel www.youtube.com/watch?v=FeaI6541z7o The Back panels must be flush with the Base. A = B Make sure the measurements are the same.
- Page 17 x 16 Only use 1 Screw to fit each Bracket Finished front edge...
- Page 18 Finished front edge IMPORTANT: The Back panel must slot into the groove in the Top panel...
- Page 19 WARNING! In order to prevent overturning this product must be used with the 2 wall attachment devices provided See the next section for a guide to wall mounting and fixings Slide the Brackets against the wall. Fit the 2nd screws supplied with the Brackets into the underside of the Top panel.
- Page 20 A Guide to Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are supplied with your are suitable for supporting your unit.
- Page 21 Finished front edge...
- Page 22 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.com/watch?v=b4NeCGnpjP8 Press the screws into the holes in the panels When the hinges have been pushed in, tighten up their screws Repeat for all doors...
- Page 23 Pre-mounted Hinge Fitting & Adjustment https://www.youtube.com/watch?v=b4NeCGnpjP8 Adjust the Door if required Height adjustment. Loosen screws A on Hinge Plates and move Door up or down as required. Retighten screw A. Forward and Back adjustment. Loosen screw B on Hinge Plate and move door in or out as required.
- Page 24 Assembly is complete Please remove any blue protective film from panel edges and clear protective film from panel surfaces ALR3718...
Need help?
Do you have a question about the JENSON 891/7944 and is the answer not in the manual?
Questions and answers