1. Manuals
  2. Brands
  3. Strong Manuals
  4. Industrial Equipment
  5. Floor-Mate 80E
  6. Owner's manual

Strong Floor-Mate 80E Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Type: Floor-Mate 80E
Model:
Serial Number:
1

Advertisement

Table of Contents
loading

Related Manuals for Strong Floor-Mate 80E

Summary of Contents for Strong Floor-Mate 80E

  • Page 1 Type: Floor-Mate 80E Model: Serial Number:...
  • Page 2 Floor-Mate 80E Owner’s Manual Strong Manufacturing Co., Inc. PO Box 8068 Pine Bluff, AR 71611 800-238-5042 870-535-4753 Fax 870-535-4843...

  • Page 3: Table Of Contents

    Table of Contents Preface Important General Safety Information 5-10 A. Material Hose B. Pump C. Electronics D. Guards E. Mixer F. Eye Protection G. Machinery 9-10 H. Water Operation 11-14...

  • Page 4: Preface

    The Floor-Mate 80E machine by Strong Manufacturing Company, Inc. is specifically designed to convey, mix, and pump cementitious slurries. We are confident that your Floor-Mate 80E will increase the efficiency of your work force. However, the service and life of the machine will depend greatly on the care and attention you give it during daily and routine use.

  • Page 5: Important General Safety Information

    Important General Safety Information The Floor-Mate 80E machine was primarily designed to mix and pump gypsum or cement, sand and water slurries. In addition to the usual hazards of machinery, several special hazards are involved in these operations. Please read and pay close attention to the following SAFETY INFORMATION.
  • Page 6 All replacement material hose and fittings should be rated for no less than 600 psi. Such hoses can be obtained from Strong Manufacturing Company. Do not use other hoses unless specifically advised by the Strong Manufacturing Company. Caution: ALL HOSES SHOULD BE FITTED WITH “FULL FLOW”...

  • Page 7: Pump

    B. Pump 1. When removing a section of hose, pressure must be relieved before undoing a fitting. This can be done by putting the pump in reverse and running it slowly until the discharge hose at the pump becomes soft. Failure to do this will result in the hose being under pressure when the fitting is undone, and material being blown out when disconnected, striking the face and eyes with the danger of injury or blindness.

  • Page 8: Guards

    PROTECTORS SHOULD BE WORN AT ALL TIMES WHEN OPERATING OR WORKING ON THIS EQUIPMENT. D. Guards BE SURE ALL MACHINERY GUARDS ARE IN PLACE BEFORE OPERATING THE FLOOR-MATE 80E. THE GUARDS PROVIDED WITH THIS MACHINE CONSIST OF THE FOLLOWING: • MIXER INLET GRATE • WET MATERIALS HOPPER GRATE/SCREEN •...

  • Page 9: Mixer

    E. Mixer Caution: ALWAYS WEAR SAFETY GOGGLES WHEN OPERATING OR WORKING AROUND THE MIXER. NEVER WEAR LOOSE CLOTHING OR HAVE LOOSE ARTICLES AROUND THE MIXER. ALWAYS TEST THE SAFETY KILL SWITCH BEFORE MIXING BEGINS. KEEP HANDS AND CLOTHING CLEAR OF MIXER AREA.

  • Page 10: Water

    3. Never operate machine with worn parts or loose parts that need adjustment. 4. Make sure all guards are in place before starting motor or engine. 5. Never operate equipment without having a BC dry chemical fire extinguisher available that is charged and in good operational condition. 6.

  • Page 11: Operation

    Be sure all guards are in place and all services have been performed. The Floor-Mate 80E is a multi-purpose machine when equipped with optional components. It may be used to mix, pump and spray cementitious slurries. The unit consist of a 7.5HP electric motor that powers the material pump, an electrically driven (1.5 HP) patented double drum...
  • Page 12 After all the aggregate has been added, allow the mixer to mix for 1 to 3 minutes depending on the type of product. After thoroughly mixing, open the mixer door allowing the material to flow into the pump hopper. Close the mixer door. Start the pump. Watch for material hose plugging on the first batch.
  • Page 13 Close the door or replace the plug. Open the mixer door and allow the water to flow into the pump hopper. Engage the pump. After running the pump for several seconds disengage the pump and reverse to relieve hose pressure. Disconnect the hose. Wet a rag or sponge and place into the hose.
  • Page 14 Caution: • AT NO TIME SHOUD ANY CLEAN UP OR SERVICE, WHERE ONE WOULD BE EXPOSED TO MOVING COMPONENTS, BE PERFORMED ON THIS EQUIPEMNT WITHOUT SHUTTING IT OUT. • DO NOT OPERATE THIS EQUIPMENT FROM ANY LOCATION EXCEPT THE OPERATOR’S STATION. •...
  • Page 15 MATERIAL SIZE DWG. NO. 0400031 (3), 0400054 (1), 0400063 (1), 0400067 (1), 0400064 (1), 1410135 (4) 21300312 DRAWING IS THE SOLE PROPERTY OF Strong Manufacturing. ANY # ECN DATE DESCRIPTION FINISH REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF...
  • Page 16 THE INFORMATION CONTAINED IN THIS 12207 1/5/20 MATERIAL SIZE DWG. NO. 04610402 DRAWING IS THE SOLE PROPERTY OF Strong Manufacturing. ANY # ECN DATE DESCRIPTION FINISH REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF Strong Manufacturing IS...
  • Page 17 THE INFORMATION CONTAINED IN THIS 12195 11/20/20 MATERIAL SIZE DWG. NO. 08360502 DRAWING IS THE SOLE PROPERTY OF Strong Manufacturing. ANY # ECN DATE DESCRIPTION FINISH REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF Strong Manufacturing IS...
  • Page 18 MATERIAL THE INFORMATION CONTAINED IN THIS RAW MATERIAL #: DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. Strong Manufacturing Inc. ANY FINISH REPRODUCTION IN PART OR AS A WHOLE 15008312 WITHOUT THE WRITTEN PERMISSION OF Strong Manufacturing Inc IS...
  • Page 19 THE INFORMATION CONTAINED IN THIS 12227 2/11/21 MATERIAL SIZE DWG. NO. 23701122 DRAWING IS THE SOLE PROPERTY OF Strong Manufacturing. ANY # ECN DATE DESCRIPTION FINISH REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF Strong Manufacturing IS...

Table of Contents