Buderus FM441 Installation Instructions Manual

Buderus FM441 Installation Instructions Manual

Modules for logamatic 4000 control panels

Advertisement

Installation Instructions
FM441
FM445
FM442
FM447
FM443
FM448
7 747 012 082-01.1RS
FM456
FM457
FM458
Modules for
Logamatic 4000
control panels
For heating
contractors
Please read carefully
prior to installation.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FM441 and is the answer not in the manual?

Questions and answers

Summary of Contents for Buderus FM441

  • Page 1 Installation Instructions Modules for Logamatic 4000 control panels 7 747 012 082-01.1RS FM441 FM445 FM456 For heating contractors FM442 FM447 FM457 FM443 FM448 FM458 Please read carefully prior to installation.
  • Page 2: Table Of Contents

    Contents Introduction ........3 Definition of the various modules .
  • Page 3: Introduction

    Introduction Introduction These installation instructions explain the installation of the FM4xx function modules in the Logamatic 4000 control panel series. USER NOTE In general, you can also use these installation instructions for the installation of other modules since the procedures are similar. Definition of the various modules Definitions CM = Controller module...
  • Page 4: Modules And Their Identification (Names)

    ZM432 Burner + boiler circuit functions Burner + boiler circuit functions + ZM434 0 – 10 % burner control ZM425 Display module FM441 1 heating zone + 1 DHW consumer FM442 2 heating zones FM443 Solar circuit FM445 LAP/LSP (charging system) FM447 Strategy...
  • Page 5: Safety

    Safety Safety About this manual This chapter contains general safety instructions that must be observed when installing the FM4xx function modules in the Logamatic 4000 control panels. Also closely observe additional safety instructions in other chapters of these installation instructions. Read the safety instructions carefully before starting the installation.
  • Page 6: Standards, Regulations And Directives

    Safety Standards, regulations and directives USER NOTE Observe all regulations and standards applicable to installation and operation of the system in your country. SER NOTE All electrical components must be approved for the USA and Canada! This product has been tested and certified and meets applicable standards for the US and Canadian markets.
  • Page 7: Please Observe These Notes

    Safety USER NOTE Tip for optimum use of equipment and adjustment as well as useful information. Please observe these notes The FM4xx function modules have been designed and manufactured in accordance with currently recognized standards and safety requirements. However, damage resulting from improper installation cannot be completely prevented.
  • Page 8: Disposal

    If there is no circuit breaker, you will need to install one. USER NOTE Only use original Buderus spare parts. Damage as a result of the use of spare parts not supplied by Buderus are excluded from the Buderus warranty.
  • Page 9: Module Installation For Logamatic 43Xx Controls

    43xx Identification 4311 4312 4321 4322 4323 CM431 NM482 ZM432 – – – ZM433 – – – – ZM434 – FM441 FM442 Modules FM443 FM445 FM447 – – FM448 FM456 – – – – FM457 – – – – FM458 ZM426 –...
  • Page 10 The FM441 and FM445 modules must never be installed together in the same control panel. If a FM441 module is already integrated into the control panel, you must remove it before installing an FM445. If you install both modules (FM441 and FM445), this will cause an error message on the display of the MEC2.
  • Page 11: Arrangement Of Modules In The Control Panel

    Module installation for Logamatic 43xx controls Arrangement of modules in the control panel 6 720 618 335-01.1RS Fig. 1 Layout of slots Slot 1 for additional module Slot 2 for additional module Slot 3 for additional module Slot 4 for additional module Slot B behind MEC2 remote control Slot A for central module ZM432 or ZM434 (standard equipment) USER NOTE...
  • Page 12 Module installation for Logamatic 43xx controls Example Heating zone assignment for two heating zone modules (FM442) and one heating zone and DHW module (FM441): 6 720 618 335-02.1RS Fig. 2 Example of the layout of function modules Slot 1 Slot 2...
  • Page 13: Installation

    Module installation for Logamatic 43xx controls Installation Fig. 3 Removing covers RISK OF LIFE due to electrical current when the control panel is open. Before opening the control panel: WARNING! isolate all poles of the power supply and secure against accidental reconnection.
  • Page 14 Module installation for Logamatic 43xx controls Fig. 4 Module installation and removal To install a new module Remove blank from slot 1 ( Fig. 4) in the control panel. Connection cables for sensors and pumps must be laid before installation of the module and provided with terminals (for more detailed information, please see the technical documentation for the Logamatic 43xx control panels).
  • Page 15 Module installation for Logamatic 43xx controls When removing and replacing a module Loosen all the connectors of the module in question and fix in park position (for more detailed information, please see the installation instructions for the Logamatic 43xx control panels). Remove module from the control panel.
  • Page 16 Module installation for Logamatic 43xx controls Position terminal cover and fasten with the screws. Test the function of the modules. For more detailed information, see the operating or service instructions for the Logamatic 43xx control panels. USER NOTE If no 120 V power supply for the module or its 120 V components is installed (e.g.
  • Page 17 Notes Modules for Logamatic 4000 control panels - We reserve the right to make technical modifications.
  • Page 18 Notes Modules for Logamatic 4000 control panels - We reserve the right to make technical modifications.
  • Page 19 Notes Modules for Logamatic 4000 control panels - We reserve the right to make technical modifications.

This manual is also suitable for:

Fm442Fm443Fm445Fm447Fm448Fm456 ... Show all

Table of Contents