Table of Contents
Advertisement
ENGLISH
Tip of the sanding base (fig. D
When the sanding base tip (5) or tip holder (4) is worn, it can
be reversed or replaced. Spare parts are available from your
BLACK+DECKER dealer.
Remove the screw (7).
u
Reverse or replace the worn part.
u
Fit and tighten the screw.
u
Finger attachment (fig. D
The finger attachment is used for fine detail sandin
Remove the screw (7).
u
Remove the diamond-shaped tip holder (4) from the
u
sanding base.
Fit the finger attachment (6) onto the sanding base
u
Fit and tighten the screw.
u
Fit the appropiate sanding sheet (11) onto the finge
u
attachment.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Do not cover the ventilation slots when using the
tool. Hold the tool as shown in fig. H. Make sure that th
sanding base is flat on the workpiece
Connecting a vacuum cleaner (fig. F
The tool has an adaptor to connect it to a vacuum cleaner
when sanding wood. To connect the tool to a vacuum cleaner,
proceed as follows:
Warning! Make sure that the tool is switched off and
unplugged.
Fit the dust extraction connector (2) onto the adapter at
u
the back of the tool.
Connect the hose of a suitable vacuum cleaner to the
u
connector.
Switching on and off (fig. G
Warning! Before connecting the tool to the power supply,
make sure it is switched off.
To switch the tool on, press the part of the on/off switch (1)
u
marked 'I'.
To switch the tool off, press the part of the on/off switch (1)
u
marked '0'.
Accessories
The performance of your tool depends on the accessory
used. BLACK+DECKER accessories are engineered to high
quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
6
(Original instructions)
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool using a
u
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
V
Input voltage
AC
W
Power input
min
No-load speed
kg
Weight
Level of sound pressure according to EN 62841:
Sound pressure (L
) 65 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 76 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
(a
) 12.5 m/s
2
h
-1
, uncertainty (K) 1.5 m/s
2
BEW230
230
55
11,000
0.8
Advertisement
Table of Contents
