Related Manuals for Fidelis 10G
Summary of Contents for Fidelis 10G
- Page 1 QUICK START GUIDE ® Fidelis Network High Capacity Collector Rev-J Collector Controller 10G (HP DL360-G10) and Collector XA4 (DL380-G10) Platforms www.fidelissecurity.com...
-
Page 2: System Overview
Fidelis Network sensors (e.g., Direct, Internal, Mail and Web Sensors) and stores it for ongoing analysis. A Fidelis Collector cluster of appliances consist of one or two Collector Controller(s) and typically three or more Collector XA database nodes. - Page 3 Logical network information: IP addresses, hostnames (Section Appendix For Fidelis Network Software version 9.3.3 and later, the appliance system type (Appendix 3. Collector: Network Port and Cabling Requirements Each appliance must be connected to the various networks with appropriate cables and in some cases, transceivers.
- Page 4 Use the tables below to identify the count and type of switch ports necessary to support the number of appliances for your deployment. Admin Network The Admin Network connects the Collector Controller to the Fidelis Network sensors and CommandPost/K2 systems. Also connects the Collector XA nodes to the CommandPost/K2. Appliance Switch Port Type Qty.
-
Page 5: Appliance - Logical Network Configuration
QUICK START GUIDE Fidelis Network® High Capacity Collector DB Network The DB Network allows communication between Collector Controller and Controller XA nodes. This network must be independent from other networks. IPv4 addressing only. Appliance Switch Port Type Qty. Collector Controller 10G... -
Page 6: Appliance Installation
QUICK START GUIDE Fidelis Network® High Capacity Collector Sample Network Configuration Table Network Setting Assignments Interface Admin/eth0 DB/eth1 SYNC/eth2 iLO/IPMI Hostname (FQDN) collector- xa1.organization.net Static IP Address 10.1.2.3 192.168.1.3 172.16.1.3 10.2.3.3 Subnet Mask 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 Gateway 10.1.2.1 10.2.3.1 Proxy Server 10.5.6.7... - Page 7 Using the connectors and cables described in sections 3 and 4, begin to connect the appliances to the networks. Refer to the Collector Network Diagram below. To cable the Collector Controller 10G appliance(s) to the switches: 1. Connect the Admin (eth0) port to the “ADMIN” switch port.
-
Page 8: Appliance Network Configuration
6. Change to root using the default password 7. From the command line, run /bin/bpctl_start /bin/bypass_util all set_force_bypass off 8. Run the following to start the Fidelis Setup program: /FSS/bin/setup 9. Within Setup, select Network Settings. www.fidelissecurity.com ©Fidelis Cybersecurity... -
Page 9: Cluster Setup
QUICK START GUIDE Fidelis Network® High Capacity Collector 10. Configure the network parameters for the system and each active network interface. • Use the Network Configuration table you prepared earlier. • When complete, return to the top menu. 11. When complete, select OK to leave Setup. - Page 10 License Agreement (EULA). CommandPost/K2 will then communicate with the Collector at the specified IP address. Register Collector Controller 10Gs with the Fidelis Sensors 1. Log into the CommandPost/K2 user interface from a web browser. 2. Navigate to System > Components 3.
-
Page 11: Appendix A: Network Configuration Worksheet
QUICK START GUIDE Fidelis Network® High Capacity Collector Appendix A: Network Configuration Worksheet Collector Controller 10G (Primary) Network Setting Assignments Interface Admin/eth0 DB/eth1 iLO/IPMI Hostname (FQDN) Static IP Address Subnet Mask Gateway Proxy Server DNS Servers NTP Servers Time Zone... - Page 12 QUICK START GUIDE Fidelis Network® High Capacity Collector Collector XA4 (A) Network Setting Assignments Interface Admin/eth0 DB/eth1 SYNC/eth2 iLO/IPMI Hostname (FQDN) Static IP Address Subnet Mask Gateway Proxy Server DNS Servers NTP Servers Time Zone Collector XA4 (B) Network Setting...
-
Page 13: Appendix B: System Specifications
QUICK START GUIDE Fidelis Network® High Capacity Collector Collector XA4 (C) Network Setting Assignments Interface Admin/eth0 DB/eth1 SYNC/eth2 iLO/IPMI Hostname (FQDN) Static IP Address Subnet Mask Gateway Proxy Server DNS Servers NTP Servers Time Zone Appendix B: System Specifications Collector Controller 10G... -
Page 14: Appendix C: System Types
Fidelis Network® High Capacity Collector Appendix C: System Types For Fidelis Network Software version 9.3.3 and later, the table below shows the software to apply based on the appliance SKU. You can find the SKU in the following locations: (Note that the SKU starts with “FSS” and “FNH”.) •...