Fidelis Network Collector SA Rev-1 Series Quick Start Manual
  1. Manuals
  2. Brands
  3. Fidelis Manuals
  4. Network Hardware
  5. Network Collector SA Rev-1 Series
  6. Quick start manual

Fidelis Network Collector SA Rev-1 Series Quick Start Manual

Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
QUICK START GUIDE
Fidelis Network®
Collector SA
Rev-I
Collector SA Appliances
Based on HP DL360-G10 Platforms
www.fidelissecurity.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Network Collector SA Rev-1 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Fidelis Network Collector SA Rev-1 Series

Summary of Contents for Fidelis Network Collector SA Rev-1 Series

  • Page 1 QUICK START GUIDE Fidelis Network® Collector SA Rev-I Collector SA Appliances Based on HP DL360-G10 Platforms www.fidelissecurity.com...

  • Page 2: System Overview

    Fidelis Network® Collector SA 1. System Overview The Fidelis Collector is the security analytics database for Fidelis Network. The Fidelis Collector SA receives network metadata from Fidelis Network sensors (i.e., Direct, Internal, Mail, and Web sensors) and stores it for ongoing analysis. The Collector SA appliance Rev-I is also referred to as Collector SA2.
  • Page 3 Logical network information: IP addresses, hostnames (Section Appendix For Fidelis Network Software version 9.0.5 and later, the appliance system type (Appendix 3. Collector: Network Port and Cabling Requirements Each component must be connected to the various networks with appropriate cables. The tables below describe the physical connection and cable type associated with each port.

  • Page 4: Appliance - Logical Network Configuration

    Use the tables below to identify the count and type of switch ports necessary to support the number of appliances for your deployment. Admin Network The Admin network connects the Collector SA to the Fidelis Network sensors and CommandPost/K2 systems. Appliance Switch Port Type Qty.

  • Page 5: Appliance Installation

    2. Connect to the component CLI using one of the following methods: Via KVM Console: Connect a keyboard − and monitor to the appliance. For Fidelis Network appliances version − 9.0.5 or later, the screen on the right is displayed: www.fidelissecurity.com...
  • Page 6 − 6. From the command line, run: sudo /FSS/bin/setup You will be prompted for the SU (fidelis) password. 7. Within Setup, select Network Settings. 8. Configure the network parameters for the system and each active network interface.
  • Page 7 4. In the left navigation, select the appropriate item for the sensor Direct, Internal, or Mail. 5. Click the Advanced or Metadata tab for the sensor. 6. In the Send metadata to collector list, select the Collector from the list. 7. Repeat for each Fidelis sensor. www.fidelissecurity.com ©Fidelis Cybersecurity...

  • Page 8: Appendix A: Network Configuration Worksheet

    QUICK START GUIDE Fidelis Network® Collector SA Appendix A: Network Configuration Worksheet Collector SA Network Setting Assignments Interface: Admin/eth0 iLO/IMM Hostname (FQDN) Static IP Address Subnet Mask Gateway Proxy Server DNS Servers NTP Servers Time Zone Appendix B: System Specifications...

  • Page 9: Appendix C: System Types

    Fidelis Network® Collector SA Appendix C: System Types For Fidelis Network Software version 9.0.5 and later, the table below shows the software to apply based on the appliance SKU. You can find the SKU in the following locations: (Note that the SKU typically starts with “FSS” or “FNH”.) Appliance lid UID decal (see sample on right) •...

This manual is also suitable for:

Network collector sa2 series

Table of Contents