Baldan ASDA Instruction Manual

Baldan ASDA Instruction Manual

Subsoiler plow with automatic shank

Advertisement

Quick Links

ASDA
Subsoiler Plow with Automatic Shank

Advertisement

Table of Contents
loading

Summary of Contents for Baldan ASDA

  • Page 1 ASDA Subsoiler Plow with Automatic Shank...
  • Page 3 Any solicitation of warranty, please contact our Baldan technical service, by your Baldan dealer that you bought our implement. Reaffirm the necessity to read carefully of warranty certificate and note all of items from this manual, therefore you will...
  • Page 4 ASDA Subsoiler Plow with Automatic Shank...
  • Page 5: Table Of Contents

    Hitching ASDA-CR / ASDA-DR ......................................................Hitching ASDA-H ..........................................................Centralization ASDA-H ........................................................Levelling of the subsoiler........................................................06. Adjustments and operations..............................................Depth adjustments asda-cr and asda-dr ..................................................Depth adjustment..........................................................Adjustment of the automatic tyne release ..................................................Cutter disc blade adjustments ......................................................07. Operation ....................................................
  • Page 6: Safety Rules

    • Read this instruction manual carefully to • Only start the tractor operations, when • Never carry people over the tractor or know the recommended safety rules. are you properly accommodated and with equipment. the seat belt fasted. Instruction Manual ASDA - 4...
  • Page 7 ALCOHOL AND DRUGS MAY GENERATE LOSS OF REFLEX AND CHANGING OF OPERATOR FISICAL CONDITIONS. SO DO NOT WORK WITH THIS EQUIPMENT, IN USE OF THIS SUBSTANCE. IN USE OF THIS SUBSTANCE. IN USE OF THIS SUBSTANCE. IN USE OF THIS SUBSTANCE. PMENT, IN USE OF THIS SUBSTANCE. Instruction Manual 5 - ASDA...
  • Page 8 BEBIDAS ALCOHOLICAS O ALGUNOS MEDICAMENTOS PUEDEN GENERAR LA PERDIDA DE REFLEJOS Y ALTERAR LAS CONDICIONES FÍSICAS DEL OPERA- DOR. POR ESTO, NUNCA TRABAJE CON ESTE EQUIPO, CASO ESTEA USANDOS ESTAS SUBSTANCIAS. Instruction Manual ASDA - 6...
  • Page 9 Do not turn on the tractor in a closed place without appropriate ventilation because the fumes from the fuel are is bad for health. While maneuvering the tractor to clamp the implement be sure that there is enough space and nobody is too close, maneuver always in slow gear and be ready to brake in case of emergency. Instruction Manual 7 - ASDA...
  • Page 10 Drugs and alcohol will affect an operator’s alertness and coordination. Do not operate any engine under these conditions. Explain the operation, inspection and maintenance instructions to those users or operators who can not read. Instruction Manual ASDA - 8...
  • Page 11: Components

    ASDA - SUBSOILER PLOW WITH AUTOMATIC SHANK 02. COMPONENTS 01 - Hitch Shackle 02 - Hitch beam 03 - Hitch beam adjuster 04 - Discs 05 - Hydraulic piston 06 - Roller fixation support 07 - Roller oscilation bar 08 - Roller compression...
  • Page 12 ASDA-CR - SUBSOILER PLOUGH, REMOTE CONTROL ASDA-H - MOUNTED SUBSOILER PLOUGH WITH AUTOMATIC SHANK Figure 2 Figure 3 Instruction Manual ASDA - 10...
  • Page 13: Technical Specifications

    260 - 325 ASDAH - Mounted subsoiler plough BALDAN reservase el derecho de cambiar las características técnicas de este producto sin prévio aviso. ASDACR - Subsoiler plough, remote control Las especificaciones técnicas són aproximadas y informadas en condiciones normales de trabajo.
  • Page 14: Assembly

    Notice the frame the marked spots where the tyne assembly will be attached on. 04 - Introduce the tyne assembly (1) onto the bar (2) put the bolts (3) and tighten with the washers and nuts (4). Instruction Manual ASDA - 12...
  • Page 15 06 - Notice that all models have an odd number of tyne assemblies. Start mounting the center unit first and work your way out laterally. Observing the 375 mm spacement. ASDA 5 Tynes ASDA 9 Tynes Figures 5 ASDA 11 Tynes...
  • Page 16 (6). the frame with the lock pin (8) washer and cotter pin (9). 09 - Mount the complete wheel (7) on the axle and fix with the nuts (8). Figure 6 Figure 7 Instruction Manual ASDA - 14...
  • Page 17 The cutting discs must be assembled in alignment with the rods. nection diagram next on figure 08). Do not reverse the hose con- nections. Make sure the hoses ends do not touch the ground). Figure 8 Figure 9 Instruction Manual 15 - ASDA...
  • Page 18 Couple the crushing roll (8) to the sway bar (5) with the screw (9), washer and nut (10). 16 - Then, place the spring (11) between the sway bar (5) and the support (1) using the pins (12), washers and locks (13). Instruction Manual ASDA - 16...
  • Page 19: Hitching To The Tractor

    Make sure if the tractor has the front and wheel weights. 03 - Ballast the wheels according to the manufactures specifica- tions. HITCHING ASDA-CR / ASDA-DR 04 - Adjust the height of the coupling header through the regulator (1). Couple the sub- soiler to the tractor drawbar using the pin (2).
  • Page 20: Hitching Asda-H

    “B” support of the subsoiler. “C” 09 - Finally, using the “D” height regu- “D” lator leveler, hitch the inferior right arm into the “C” support accor- ding to the figure. Figure 12 Instruction Manual ASDA - 18...
  • Page 21: Centralization Asda-H

    Both arms should be also at the same level between each other, figure 13. 11 - The top link will be now in line with the tractor center line. Figure 13 Instruction Manual 19 - ASDA...
  • Page 22: Levelling Of The Subsoiler

    (wifth). 14 - The longitudinal levelling (lenght) is done through the 3rd point arm. 15 - Note that the rods should be parallel to the ground according to figure 14. “ A ” Figure 14 Instruction Manual ASDA - 20...
  • Page 23: Adjustments And Operations

    06. ADJUSTMENTS AND OPERATIONS DEPTH ADJUSTMENTS ASDA-CR AND ASDA-DR 01 - The working depth of the strips is limited by the wheels (1) which are acti- vated by the hydraulic cylinders (2). 02 - Determine the working depth of the strip, immediately lift the wheels via hydraulic cylinders up to the extent determined, place the rings limiters (3) in the cylinder rods.
  • Page 24: Depth Adjustment

    DEPTH ADJUSTMENT ADJUSTMENT OF THE AUTOMATIC TYNE RELEASE 04 - The depth control of the mounted ASDA-H is done by adjusting the 06 - The automatic tyne disarming are shipped with determined resis- wheels (1). To do this, loosen bolts (2) move the wheel up or down tance regulation, ie with 33.5 cm in width of the spring.
  • Page 25: Cutter Disc Blade Adjustments

    The spring (4) leaves the factory with calibrated pressure, no more pressure on it to neutralize no joint action cutting blades. IMPORTANT Note that the cutting blade should always be aligned with the tyne. The depth adjustment of the discs must be equal for all sets. Figure 18 Instruction Manual 23 - ASDA...
  • Page 26: Operation

    When operating with subsoiler, locate a gear that allows the tractor to maintain a certain reserve of power, ensuring against unforeseen efforts. 06 - The operating speed varies according to ground conditions, recommend an average of 4.5 to 5 km / hour. Figure 19 Instruction Manual ASDA - 24...
  • Page 27: Preparing The Subsoiler For Transportation

    If there is a need to raise a roller, use proper equipment. Before performing the operation lift the roller, release the springs between the bars and swing su- pport rods, as shown in figure 20. Instruction Manual 25 - ASDA...
  • Page 28: Maintenance

    Before starting lubrication, clean all grease fittings with a clean, lint-free cloth and replace any Bardahl Maxlub APG 2 EP that are damaged. Table 3 If there were other manufacturers or and other. Equivalent trends that are not listed in this. Table, consult the manufacturer’s technical manual. Instruction Manual ASDA - 26...
  • Page 29 LUBRICATION POINTS Lubricate every 10 hours Figure 21 Instruction Manual 27 - ASDA...
  • Page 30 LUBRICATION POINTS Lubricate every 60 hours Lubricate every 100 hours Figures 22 Instruction Manual ASDA - 28...
  • Page 31: Bearings Adjustments

    10 - The bearing must rotate freely, ie without axial or radial clearances. 11 - Grease the bearing again. The amount of grease used is 150 grams. Instruction Manual 29 - ASDA...
  • Page 32: Cleaning

    When the implement is not going to be used for a longer period we recommend to store it in good conditions for conservation. Clean and grease, patch up paint, spray oil over the implement and points before storage. Figure 24 Instruction Manual ASDA - 30...
  • Page 33: Identification

    11. IDENTIFICATION 01 - In order to refer parts catalogues or apply technical support from Baldan, always indicate model (1), serial number (2), manufacture date (3) loca- ted on the identification tag. ALWAYS REQUIRE BALDAN ORIGINAL PARTS Code: 6055010081-1 PUBLICATIONS...
  • Page 34 Do the identification below to always have the properly informations about your equipment life time. Owner: _______________________________________________________________________________________________________________ Dealer: _______________________________________________________________________________________________________________ Farm: ________________________________________________________________________________________________________________ City: ______________________________________________________ Country: ___________________________________________________ Model: _______________________________________________________________________________________________________________ Warranty certified number: ____________________________________ Serial number: ______________________________________________ Purchase date: ________/ __________/ __________ _____Invoice. Nr: ___________________________________________________________ Instruction Manual ASDA - 32...
  • Page 35: Note

    NOTE: Instruction Manual 33 - ASDA...
  • Page 36 07 - It is out of this term the product wich has repairs or modifications not made by dealers from Baldan’s network, as well as pieces applications or not authentic components to the product by the user.
  • Page 37 (in case of requested). Baldan keeps the right of changing and or improve the technical characteristics of its products, without notice and without the obligation of act 15 -...
  • Page 39 INSPECTION AND DELIVERY CERTIFICATE SERVICE BEFORE THE DELIVERY: This equipment was very carefully prepared by the dealer’s organization, inspected in all its parts in agreement • with the manufacture’s prescription. • DELIVERY SERVICE: The user was informed about the current guarantee terms and instructed about maintenance care and utilization. •...
  • Page 41 INSPECTION AND DELIVERY CERTIFICATE SERVICE BEFORE THE DELIVERY: This equipment was very carefully prepared by the dealer’s organization, inspected in all its parts in agreement • with the manufacture’s prescription. • DELIVERY SERVICE: The user was informed about the current guarantee terms and instructed about maintenance care and utilization. •...
  • Page 43 Owner: _______________________________________________________________ Phone: _______________________________________________________________ Adress: _______________________________________________________________________________________________________ Number: ______________________ City: _________________________________________________________________ State: ________________________________________________________________ E-mail: _______________________________________________________________________________ Date of sale: ___________________________________________ 3ª Page - Manufacturer _______________ Signature / Store’s stamp ________________________________________________________________ Please send this filled copy to Baldan, until 15 days after the purchase.
  • Page 46 Instruction Manual ASDA - 4...

Table of Contents