Advertisement
FM wire aerial
The iPod & iPhone and VOLUME + buttons have a tactile dot.
Note
Setting the clock
If you try to store another station with the same
preset number, the previously stored station will
1
Plug in the unit.
be replaced.
2
Press and hold CLOCK until the hour
Preset tuning mode
flashes in the display.
1
The hour starts to flash in the display.
Press FM to turn on the radio.
3
Press ALARM/CLOCK + or – repeatedly
Check that the preset mode is selected.
2
Press TUNE/PRESET or to
to set the hour.
4
select the desired preset number.
Press CLOCK.
3
5
Adjust the volume using
Repeat steps 3 and 4 to set the minute,
VOLUME + or –.
and then press CLOCK.
The seconds start incrementing from zero.
Manual tuning mode
Notes
1
Press FM to turn on the radio.
If you do not press any button for about 1
minute while setting the clock, the clock setting
Check that the manual tuning mode is
will be canceled.
selected.
2
The clock system varies depending on the
Press TUNE/PRESET or to
model you own.
tune in to a desired frequency.
12-hour system: "AM 12:00" = midnight
3
Adjust the volume using
AC power
24-hour system: "0:00" = midnight
adaptor
VOLUME + or –.
When pressing any of the rear buttons, hold the
unit firmly to prevent slippage.
Note
To change the display to the daylight
The FM frequency display is raised or lowered by
a step of 0.1 MHz. For example, frequency 88.00
saving time (summer time) indication
and 88.05 MHz is displayed as "88.0 MHz. "
Change the daylight saving time (summer time)
adjustment setting according to the following
Tuning in to a station
procedures.
The unit automatically scan FM stations.
1
Press DST/SUMMER TIME.
Press FM to turn on the radio.
" " appears in the display and the time indication
Check that the manual tuning mode is
changes to the daylight saving time (summer
selected.
time).
2
Press and hold TUNE/PRESET or
To deactivate the daylight saving time (summer
.
time) adjustment, press DST/SUMMER TIME
: scans upward through the frequency
again. " " disappears.
bands.
: scans downwards through the
frequency bands.
Setting the brightness
Scanning starts from the currently-tuned
of the display
frequency. When a station is received,
scanning stops.
3
Four levels of brightness are available by pressing
Adjust the volume using
SNOOZE/BRIGHTNESS.
VOLUME + or –.
Improving the
reception
Operating the radio
FM: Extend the FM wire aerial fully to increase
There are two ways to tune.
reception sensitivity.
To switch between the two tuning methods
(manual tuning or preset), press TUNE MODE/
Notes on radio reception
ENTER MEMORY.
Keep digital music players or mobile phones
Auto preset
away from the FM aerial, as this may lead to
reception interference.
You can preset 20 stations for FM.
When you are listening to the radio with an
1
Press FM to turn on the radio.
iPhone connected to the unit, interference with
2
Press and hold FM until "AP" appears in
radio reception may occur.
When you are listening to the radio while
the display.
charging an iPod, interference with radio
3
Press TUNE MODE/ENTER MEMORY.
reception may occur.
The unit automatically presets the available
Do not place the FM aerial close to the AC
channels in order.
power adaptor as noise may result.
If a station cannot be preset
automatically
Operating an iPod
You need to preset a station with a weak signal
manually.
You can enjoy audio from iPod by connecting to
1
Follow steps 1 and 2 in "Manual tuning
this unit. To use an iPod, refer to the user's guide
mode" to tune the frequency you wish to
of your iPod.
preset.
If you are using an iPhone, iPhone 3G, iPhone
3GS or iPhone 4, attach the supplied universal
2
Press and hold TUNE MODE/ENTER
dock adapter for iPhone, iPhone 3G, iPhone 3GS
MEMORY for preset number until the
or iPhone 4 before connecting.
flashes.
The adapter number, , or , is shown on
3
Press TUNE/PRESET or to
the underside of the supplied universal dock
adapters. is for the iPhone, is for the iPhone
select the preset number, then press
3G & iPhone 3GS and is for the iPhone 4.
TUNE MODE/ENTER MEMORY.
Check the adapter number before use.
The frequency is stored with the selected
Universal dock adaptor
preset number.
Example: The following display appears
when you preset FM 105.7 MHz to preset
number 2 for FM.
The display shows the frequency for about 10
seconds, and then returns to the current time.
To preset another station, repeat these steps.
Notes
When inserting an iPod into the unit, be sure to
use the universal dock adaptor supplied with
your iPod or commercially available from
Apple Inc.
The connector of the unit is exclusively for use
with an iPod.
Sony cannot accept responsibility in the event
that data recorded on an iPod is lost or
damaged when using an iPod connected to this
unit.
For details of environmental conditions for
operating your iPod, check the website of Apple
Inc.
1
Attach the adaptor for your iPod/iPhone.
2
Insert your iPod/iPhone into the
connector of the unit.
3
Press iPod & iPhone .
The iPod begins to play automatically.
You can operate the connected iPod by this
unit or the buttons on iPod.
4
Adjust the volume using VOLUME + or –.
To
Press
Turn off the iPod
OFF, or press and
hold iPod &
iPhone
Pause playback
iPod & iPhone
To resume play,
press it again.
Go to the next track
Go back to the previous
*
track
Locate a point while
(forward) or
listening to the sound
(backward)
while playing and
hold it until you
find the point.
Locate a point while
(forward) or
(backward)
observing the display
in pause and hold
it until you find
the point.
* During playback, this operation goes back to
the beginning of the current track. To go back
to the previous track, press twice.
Notes
When placing or removing the iPod, hold the
iPod at the same angle as that of the connector
on this unit, and do not twist or bend the iPod
as connector damage may result.
Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
When placing or removing the iPod, hold the
iPod firmly so as not to topple the unit.
Before disconnecting the iPod, pause playback.
To use the unit as a battery charger
You can use the unit as a battery charger.
Charging begins when the iPod is connected to
the unit.
Charging status appears in the display of iPod. For
details, see the user's guide of your iPod.
On copyrights
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
"Made for iPod, " and "Made for iPhone" mean
that an electronic accessory has been designed to
connect specifically to iPod or iPhone,
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and
regulatory standards. Please note that the use of
this accessory with iPod or iPhone may affect
wireless performance.
To confirm an alarm time setting
Setting the alarm
Turn off the "ALARM" indicator in the display,
and press the ALARM ON/OFF button once.
This clock radio is equipped with 3 alarm
modes—iPod, radio and buzzer. Before setting the
To change an alarm setting
alarm, make sure to set the clock (see "Setting the
Set the alarm again.
clock").
To doze for a few more minutes
To set the alarm
Press SNOOZE/BRIGHTNESS.
The sound turns off but will automatically come
1
Press and hold ALARM SET.
on again after about 10 minutes.
"WAKE-UP" appears and the hour flashes in
You can change the snooze time by pressing
the display.
SNOOZE/BRIGHTNESS repeatedly within
2
Press ALARM/CLOCK + or – repeatedly
4 seconds.
until the desired hour appears.
The maximum length of the snooze time is
To cycle the hour rapidly, press and hold
60 minutes.
ALARM/CLOCK + or –.
To stop the alarm
3
Press ALARM ON/OFF.
Press ALARM RESET OFF to turn off the alarm.
The minute flashes.
The alarm will sound again at the same time the
4
Repeat step 2 to set the minute.
next day.
5
Press ALARM ON/OFF.
To deactivate the alarm
The alarm mode setting is entered.
Press ALARM ON/OFF to turn off the "ALARM"
6
Press ALARM/CLOCK + or – repeatedly
indicator from the display.
until the desired alarm mode flashes.
You can choose one of 3 settings: "iPod", "FM"
Note on the alarm in the event of a power
or "BUZZER. " Set the alarm mode as follows:
interruption
– iPod: see " Setting the alarm for iPod. "
In the event of a power interruption, the alarm
– FM: see " Setting the radio alarm. "
will work until the battery is totally discharged.
– BUZZER: see " Setting the buzzer alarm. "
However, certain functions will be affected as
Setting the alarm for iPod
follows:
The backlight will not light up.
1
Perform steps 1 to 6 in "To set the
If the alarm mode is set to iPod or radio, it will
change to BUZZER automatically.
alarm. "
If a power interruption occurs while the alarm
2
Press ALARM ON/OFF to select alarm
is sounding, the alarm will stop.
mode for "iPod".
If ALARM RESET OFF is not pressed, the
"VOL" appears in the display.
alarm will sound for about 5 minutes.
3
Press ALARM/CLOCK + or – to adjust
If " " appears in the display, the alarm will
the volume.
not sound in the event of power interruption.
Replace the battery if " " appears.
4
Press ALARM ON/OFF.
The snooze function will not work.
The setting is entered.
During a power interruption, the alarm will
5
If "ALARM" does not appear in the
sound at the set time only once.
display, press ALARM ON/OFF again.
The iPod will sound at the set time.
Setting the sleep timer
When using an iPod touch/iPhone
To wake up to music stored in an iPod touch/
You can fall asleep to the music, etc., using the
iPhone, connect the iPod touch/iPhone to the
built-in sleep timer that turns off the unit
unit first, follow the steps above to set alarm
automatically after a preset duration.
time, and then select the music function.
Even if the alarm setting for iPod is complete, if
1
Press SLEEP while the unit is turned on.
you turn the power of iPod touch/iPhone off
"SLEEP" appears and the sleep time flashes in
before inserting the iPod touch/iPhone into the
the display.
unit, the alarm for iPod will not work.
2
Press SLEEP to set the sleep timer
Setting the radio alarm
duration.
1
Each time you press SLEEP, the duration (in
Perform steps 1 to 6 in "To set the
minutes) changes as follows:
alarm. "
2
Press ALARM ON/OFF to select "FM"
alarm mode.
The display returns to clock mode for about
"FM", "PRESET" number or "– –" flashes.
4 seconds after you have finished the duration
"– –" is the last station received.
setting and released SLEEP, and then the sleep
3
Press ALARM/CLOCK + or – to select
timer starts.
the desired preset number or "– –".
The unit will play for the duration you set, and
4
then shut off.
Press ALARM ON/OFF.
"VOL" appears in the display.
To turn off the unit before the preset
5
Press ALARM/CLOCK + or – to adjust
time
the volume.
Press ALARM RESET OFF.
6
Press ALARM ON/OFF.
To change the sleep timer setting
7
If "ALARM" does not appear in the
You can press SLEEP repeatedly to select the
display, press ALARM ON/OFF again.
desired sleep timer setting even after the sleep
The radio will turn on at the set time.
timer has been activated.
Setting the Buzzer Alarm
To deactivate the sleep timer
1
Press SLEEP repeatedly to set the sleep timer to
Perform steps 1 to 6 in "To set the
"OFF" in step 2.
alarm. "
2
Press ALARM ON/OFF to select
"BUZZER" alarm mode.
The setting is entered.
3
If "ALARM" does not appear in the
display, press ALARM ON/OFF again.
The buzzer will sound at the set time.
Note
The volume cannot be set for the buzzer alarm.
Hide quick links:
Advertisement
