Rinse Aid And Refined Salt; Measuring Out The Rinse Aid; Measuring Out The Refined Salt - Hotpoint Ariston LTF 8B019 Operating Instructions Manual

Rinse aid and refined salt

Only use products which have been specifically designed
EN
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
(Follow the instructions given on the packaging).
very hard.
If you do not add salt or rinse aid, the LOW SALT
LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
is illuminated, a reserve supply of rinse aid is still available
on the lid;
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
(set to factory level).
display
Adjust the rinse aid supply level with the P button.
Press the ON/OFF button to save the adjustment setting.
aid will not be supplied and the low rinse aid indicator light in
case of running out.
A maximum of 4 levels can be set according to the dishwasher
model.
number number (3-4).
Setting the water hardness
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
26
*
on the control panel
"D"
by pressing and pulling up the tab
and hold the P button for a few seconds until you hear a beep.
appears on the display
Adjust the water hardness level with the P button,
see water hardness table)
Press the ON/OFF button to save the adjustment setting.
still be filled.
*
and
Water Hardness Table
level °dH
1 0 - 6
2 6 - 11
3 12 - 17
4 17 - 34
*
34 - 50
5

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
the cap of the salt dispenser;
*
is illuminated
residues away from the opening; rinse the cap under running
water and then screw it on, the head facing downwards so as to
let the water flow out of the four slots (star-shaped arrangement)
in the lower part of the cap (cap with green float
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
so that any saline solution which has leaked out of the salt
dispenser is removed.
*
Only available in selected models.
(water softener set to medium level).
up to a max. of 5 levels.
Average salt dispenser
capacity duration
°fH mmol/l months
0 - 10 0 - 1
11 - 20 1,1 - 2
21 - 30 2,1 - 3
31 - 60 3,1 - 6
61 - 90 6,1 - 9
*
cannot be seen by simply looking at
;
tank right up to its edge.
*
(see figure)
3. Position the funnel
fill the salt dispenser up to the edge
water to leak out.
*
**
and
*
).