Download Print this page

Advertisement

Quick Links

Introduction
The Remote Close accessory, shown in Figure 1, can be
installed in
800-4000
ampere frame Power Break® II
circuit breakers.
It provides
closing the circuit breaker after the springs have been
charged.
Table
lists
1
corresponding electrical data for the available models.
Figure
1.
Remote Close accessory.
Remote Operation
The circuit breaker can be closed remotely, provided
that the springs are charged, by applying voltage
terminals
and 34 on the terminal
16
right side of the breaker with a push button or similar
device.
Power BreakiD II Circuit Breaker
Accessories
a means
of remotely
the
catalog
numbers
and
block on the
Catalog No.
SPRCS024
SPRCS048
SPRCS072
SPRCS120
SPRCS125
SPRCS240
Table
1.
Electrical data for the Remote Close accessory.
GEH-62838
Remote Close
Installation
WARNING:
Before installing any accessories, tum the
breaker off, disconnect it from all voltage sources, and
discharge the charging springs.
A VERTISSEMENT:
mettre le disjoncteur en position OFF, le deconnecter
de toute tension
ressorts d'armement.
Use the following
Close accessory into the circuit breaker.
1.
Verify
that the rating
identification plate matches the electrical data
required for the application, as listed in Table
2.
Tum the breaker off and discharge the closing
spring by depressing the OFF and ON buttons in
the
sequence OFF-ON-OFF.
breaker
OFF-ON indicator
green background and that the charge indicator
shows DISCHARGED on a white background.
3.
Loosen the four Philips-head screws on the t r i m­
plate assembly and remove the trim plate.
4.
Loosen the four screws
breaker
cover.
breaker face, as illustrated in Figure
5.
Remove the screw
terminal
block to the midcover and
to
terminal block up and away from its mounting
ridge on the midcover.
Voltage
Peak Inrush
Rating
Current
24
13.2
Vdc
A
48
Vdc
6.6 A
72
5.0
Vdc
A
120
3.0
Vac
A
125
3.5
Vdc
A
240
2.0
Vac
A
Avant d'installer
tout accessoire,
d'alimentation,
et
decharger
procedure to install
the Remote
on the Remote Close
Verify
shows OFF on
at the corner
Remove
the
cover
2.
holding
the left secondary
les
1.
that
the
a
of the
from
the
lift
the

Advertisement

loading

Summary of Contents for GE SPRCS024

  • Page 1 Voltage Peak Inrush Catalog No. Rating Current SPRCS024 13.2 SPRCS048 6.6 A SPRCS072 SPRCS120 SPRCS125 SPRCS240 Table Electrical data for the Remote Close accessory.
  • Page 2 Remove Motor Operator Mechanism, present, following the reverse of the installation procedure described in GEH-6281. While holding the charge interlock rod of the breaker down against the midcover, move the Remote Close under the spring frame until it rests against the side frame of the breaker mechanism, as illustrated in Figure 3.
  • Page 3 Trouble-Shooting The following guide is provided for trouble-shooting and isolating common problems. It does not cover every possible situation. Contact the ED&C Customer Support Center at 800-843-3742 if any problem is not resolved by these procedures. Possible Cause Corrective Action The breaker does not close.
  • Page 4 Should further information be desired or should particular problems arise that are not covered sufficiently for the purchaser's purposes, the matter should be referred to the GE Company. GE Electrical Distribution & Control General Electric Company 41 Woodford Ave., Plainville, CT 06062...

This manual is also suitable for:

Sprcs048Sprcs072Sprcs120Sprcs125Sprcs240