Advertisement

Quick Links

PT01 User Manual
Version: 1
Keep this user manual for future references.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT01 and is the answer not in the manual?

Questions and answers

Summary of Contents for BenQ PT01

  • Page 1 PT01 User Manual Version: 1 Keep this user manual for future references.
  • Page 2: Table Of Contents

    Dimensions ..........4 Preparation for Setup.. 5 Environment Condition ......5 Surface Condition ........6 Projector Requirements......9 PT01 Installation........10 Connecting PT01 ........12 PT01 Laser Curtain ... 13 Adjusting PT01.........13 Driver Installation ..14 Configuration Setting ......15 Alignment Instructions....17 Alignment View ........17 Using the Alignment Masks....18...
  • Page 3: Shipping Contents

    Shipping Contents The PointWrite touch module is a touch transmitter for the BenQ PointWrite interactive projector. To use the touch module, please find the standard accessories below and follow this manual. PointWrite Touch Installation CD Quick manual Module Dummy pen with pen...
  • Page 4: Product Overview

    When replacing the pen nib on the dummy pen, take it from the dummy pen. For better touch performance, keep the pen nib clean. When replacing the pen nib, take it from the dummy pen. Product Overview About PT01 Front View Rear View Mounting Top screw...
  • Page 5: Preparation For Setup

    Preparation for Setup Environment Condition The PT01 touch module functions with an PointWrite interactive projector for scalable finger touch functionality, transforming any flat surface into a virtual interactive whiteboard. For optimal finger touch quality, follow these guidelines: Close all window curtains.
  • Page 6: Surface Condition

    Surface Condition Optimal finger touch quality is dependent on the selected surface condition. You can attach the touch module on a wall surface or existing board. It is important to choose a smooth and flat surface area free of protrusions. In the event of a projection surface not conducive to finger touch functionality, select the PointWrite pen as the pointing method for the classroom.
  • Page 7 Measuring the Flatness of the Surface Place a six-foot carpenter’s level horizontally across the projection area (board). Locate the point on the level furthest away from the projection area. Measure the surface flatness on both sides of the projection area. •...
  • Page 8 Surface Obstructions Maintain the projection area clean and free of obstructions. The following are common obstruction examples: • Cables or wires that hang into the projected image. Leave extra space between the cables and the projected image so you can make image adjustments later.
  • Page 9: Projector Requirements

    Projector Requirements The PointWrite touch module is only available for BenQ PointWrite series interactive projector. Make sure the PointWrite camera module is installed properly before you setup the PointWrite touch module. For more information, please refer to the PointWrite camera module User Manual or Quick Guide when installing.
  • Page 10: Pt01 Installation

    PT01 Installation Screen Tolerance Center line of touch area 50-100mm PT01 touch module Frame Surface Touch area 50mm 50mm 50mm Item Specification 1 Horizontal Position Center Line of beamed screen. Ceiling Mounting: Top of the screen with Gap. 2 Vertical Position Table Mounting: Bottom of the screen with Gap.
  • Page 11 Mounting PT01 Install the adhesive tape on the rear side of the PointWrite touch module. Following the instructions above to position the PT01 on the screen. 3M double tape (thickness: 1mm) is recommended. Turn over the front cover. Secure the PT01 to the wall with screws.
  • Page 12: Connecting Pt01

    Connecting PT01 Use the USB cable to connect the PT01 for power supply. There are three ways to connect the PT01. Connect PT01 to Projector (Recommended) USB type-A power is available for selected projector model. Connect PT01 to Computer USB power may be unstable under the following conditions: 1.
  • Page 13: Pt01 Laser Curtain

    Screen Height Laser curtain board Adjusting PT01 To have the best performance of PT01, adjust the laser curtain using a hex key on the screws. Top screw Left screw Right screw Pitching control Adjust top screw, the laser curtain goes up and down as the following image.
  • Page 14: Driver Installation

    Driver Installation Use the PointWrite driver in the PT01 CD to enable the finger touch function. The CD in the PointWrite pen kit does not contain the finger touch function. PointWrite Pen kit PT01 touch module kit Pen Mode Pen Mode...
  • Page 15: Configuration Setting

    Configuration Setting To use the PointWrite, the proper setting of the PointWrite configuration is needed. The Configuration setting window will help you to set up PointWrite correctly. Select Pen Mode during the setting process. Configuration Setting...
  • Page 16 When the projector is placed on the table, do not click this item. • Rear Screen Mode: If the projector is installed on the rear screen system, click this item. Select Update Server: Please visit local BenQ Website for more support. Configuration Setting...
  • Page 17: Alignment Instructions

    In PointWrite Alignment, press Alignment View to enter the camera view (refer to page 18). Check the position of the pattern image. UST-Mirrot type projector ST-Short throw projector Connect the USB cable for PT01 and go to "Using the Alignment Masks" on page 18 for alignment instructions. Alignment Instructions...
  • Page 18: Using The Alignment Masks

    Using the Alignment Masks The alignment masks help you to find the optimal height of the laser curtain and optimal touch performance. Shape of Alignment Mark Lower reflector Higher reflector Mounting Position of Alignment Mark In the camera view of PointWrite, The alignment mark reflector is shown like below picture.
  • Page 19 Adjust for Reflection Left screw Right screw Left screw Right screw Top screw Adjust the reflection laser curtain horizontally Alignment Instructions...
  • Page 20: Pointwrite Calibration

    PointWrite Calibration Auto calibration : click on and the calibration process will run automatically. When you choose this method, white image is shown on the screen and the pattern image is displayed. Manual calibration: Click on and the calibration window will be projected on the screen.
  • Page 21 Use the PointWrite pen to click on the center of calibration cursor immediately after it appears. Then the next cursor will display. Repeat this process until the last calibration cursor disappears. After completing calibration, change the mode to Finger Touch Mode. Now you can use QWrite.
  • Page 22: Specifications

    Specifications Touch module Model Name PT01 Operating Voltage 4.7~5.2V Power Consumption Max 180mA USB Type (Power) Mini USB B type Power Source Power via USB connector or 5V adaptor Wavelength 850nm ± 10nm Fan Angle Max : 180° (1 laser beam) Rolling Control Range Max 4°...

Table of Contents