Buttons And Indicators; Prior To Use - Makita DRC200 Instruction Manual

Overload
When the Robotic Cleaner is overloaded and an
abnormally high current is drawn, the Robotic Cleaner
automatically stops without any indication.
To restart the Robotic Cleaner, turn the power OFF,
eliminate the cause of the overload, and then turn the
power back ON.
Overheating
When the Robotic Cleaner overheats, the
flashes 5 or 7 times for each sequence and the Robotic
Cleaner automatically stops.
In this case, leave the Robotic Cleaner to cool down
before turning the power back ON.
Overdischarge
When the remaining battery level becomes low, the
Robotic Cleaner automatically stops and does not
respond to any switch operations.
In this case, remove and recharge the battery
cartridges.
BUTTONS AND
INDICATORS
You can find details of the parts by searching for
the figure number corresponding to each part in this
document (e.g. search for "Fig. F-8" for the
button).
Robotic Cleaner (Fig. F)
1. Pilot lamp
2. Troubleshooting lamp
3. Filter maintenance lamp
4. Brush maintenance lamp
5. Battery indicators (for the right-hand and left-
hand battery cartridges)
6. Timer button and lamps
7. Cruise mode button and lamps
: Pattern mode
: Random mode
8. POWER (start/stop) button
9. Buzzer button and lamp
10. Vacuum button and lamp
11. Boundary sensor button and lamp
Remote control (Fig. G)
1. POWER OFF button
2. Start/Stop button
3. Location beacon button
4. / Cruise mode buttons
5. Timer button
6. Buzzer button
7. Vacuum button

PRIOR TO USE

Assembly and battery installation
CAUTION: Always be sure to turn OFF the Robotic
Cleaner before carrying out any work on the Robotic
Cleaner.
lamp
Supplied accessories
Check that the items in the following list are included in
the package.
• Size AAA (LR03) batteries (x2)
• Side brushes (x4, incl. two spare brushes)
• Screws for side brush installation (x4)
• Boundary tape (15 m x1)
• Instruction Manual (x1)
• Quick start guide (x1)
• Notes on use (x1)
Installing the side brushes (Fig. A)
Install the side brushes on both sides of the bottom front
of the Robotic Cleaner.
NOTICE: Before work, be sure to spread a rug or
other cushioning material on the floor to prevent
damage to the floor and Robotic Cleaner (Fig. B).
POWER
1. Place the side brush on the rotating shaft head on
the Robotic Cleaner with the groove of the brush
fitted to the shaft head.
2. Secure the side brush using the supplied screw.
NOTICE: Make sure that the Robotic Cleaner is
operated with the side brushes installed.
Installing the battery cartridges
Align the groove (Fig. C-2) on the battery cartridge with
the tongue (Fig. C-3) on the battery dock and slip it into
place. Insert it all the way until it locks in place with a
small click.
If you can see the red indicator (Fig. C-1) on the upper
side of the release button, the battery cartridge is not
completely locked.
CAUTION: Care must be taken in installing the
battery cartridges so that fingers are not caught
between the dock and the battery cartridge.
The Robotic Cleaner operates with only one battery
cartridge installed on either of the battery dock.
To remove the battery cartridge, slide it from the battery
dock while pressing the release button (Fig. D-1) on the
cartridge.
Installing batteries in the remote control (Fig. E)
Slide off the battery compartment lid, and insert two
AAA size (LR03) batteries, taking care to align correctly
the polarity (+/–).
NOTICE: Do not use new and old batteries together,
nor use different types of battery together.
NOTICE: Remove the batteries, if the remote control
is not going to be used for a long time.
11 ENGLISH