Table of Contents
Advertisement
CLEANING THE OUTER HOUSING /
CUP WARMING PLATE
•
The outer housing and cup warming plate can
be cleaned with a soft, damp cloth (do not
use abrasive cleansers, pads or cloths which
can scratch the surface).
CLEANING THE DRIP TRAY
•
The Drip Tray should be removed, emptied and
cleaned at regular intervals, particularly when
the Drip Tray Full Indicator is showing full.
CLEANING THE FILTERS, FILTER HOLDER AND
BREWING HEAD
•
The stainless steel Filters and Filter Holder
should be rinsed under water directly after
use to remove all coffee particles. Should the
fine holes in the filters become blocked, the
fine pin on the Cleaning Tool can be used to
clear the holes.
•
The Brew Head interior should be wiped
with a damp cloth to remove any ground
coffee particles.
•
Remove the Drip Tray Full Indicator and Grid
•
Periodically run water through the machine
from the Drip Tray, wash with warm soapy
with the Filter Holder in place, but without
water, using a non-abrasive washing liquid,
any ground coffee, to rinse out any residual
rinse and dry thoroughly.
coffee particles.
26
CARE AND CLEANING
•
If further cleaning is required the full indicator
can be removed from the drip tray by
releasing the side snaps.
CLEANING THE STORAGE TRAY
•
The Storage Tray can be removed after the
Drip Tray is removed then cleaned with a soft,
damp cloth (do not use abrasive cleansers,
pads or cloths which can scratch the surface).
NOTE: Do not clean any of the parts or
accessories in the dishwasher.
DECALCIFYING
DECALCIFYING THE MACHINE
•
After regular use, hard water can cause
•
Ensure the Selector Control is in the 'Standby'
mineral build up in and on many of the inner
position, the Power On/Off button is set to
functioning components, reducing the brewing
the 'Off' position and the machine is switched
flow, power of the machine, and affecting the
off at the power outlet and unplugged.
quality of coffee.
•
Remove the Filter Holder and Frothing
•
We advise decalcifying the machine on a
Attachment. Pour the mixture of white vinegar
regular basis (every 2-3 months) using a
and water into the water tank.
mixture of white vinegar and water. Follow the
•
Plug the machine into the power outlet and
instructions provided, or use the following as
switch on.
a guide:
•
Set Power On/Off button to the 'On' position
Diluted solution (for softer water)
and the Selector Control to the 'Standby'
•
1 part white vinegar
position
•
2 parts cold tap water
•
Place a large container under both the Brew
Head and the Steam Wand.
Concentrated solution (for harder water)
•
1 part white vinegar
•
1 part cold tap water
WARNING: DO NOT IMMERSE CORD, PLUG OR APPLIANCE IN WATER OR ANY OTHER LIQUID.
•
When the brewing temperature is reached the
'Heating' light will switch off. Set the Selector
Control to the 'Espresso' position and let half
the mixture of white vinegar and water run
through the Brew Head.
•
Set the Selector Control to the 'Steam'
position and allow the remaining liquid to run
through the Steam Wand. When the liquid
stops flowing, set the Selector Control back to
the 'Standby' position.
•
After decalcifying, remove the Water Tank and
rinse thoroughly then re-fill with fresh cold
water. To rinse the machine, run half the
water through the Brew Head and half
through the Steam Wand.
•
The machine is ready for use.
THE WATER TANK SHOULD NEVER BE REMOVED OR COMPLETELY EMPTIED
DURING DECALCIFYING.
27
CARE AND CLEANING
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
