Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hover-1 AXLE
Summary of Contents for Hover-1 AXLE
- Page 1 E L E C T R I C S C O O T E R OP E RAT I ON M A N U A L H 1- A X L...
- Page 2 HELMETS SAVE LIVES! Always wear a properly tted helmet that complies with CPSC or CE safety standards when you ride your scooter. Correct Fitting: Make sure your helmet covers your forehead. Incorrect Fitting: Forehead is exposed and vulnerable to serious injury.
- Page 3 PLEASE READ THE USER MANUAL THOROUGHLY. Failure to follow the basic instructions and safety precautions listed in the user manual can lead to damage to your Axle, other property damage, serious bodily injury, and even death. Thank you for purchasing the Hover-1 Axle Electric Scooter. Please read all instructions carefully before using and retain this manual for future use and reference.
- Page 4 Axle. • Do not use the Axle if it has been dropped or damaged in any way. • Repairs to electrical equipment should only be performed by the manufacturer.
- Page 5 • Do not operate or allow others to operate the Axle until the user understands all instructions, warnings and safety features described in this manual. • Check with your doctor if you have a medical condition that could affect your ability to use the Axle.
- Page 6 Axle scooter. Operating the Axle without following the contents of this manual may lead to damage to your Axle or bodily injury. This manual is designed to give you the information you need for the safe operation and maintenance of your Axle.
-
Page 7: Specifications
The Axle uses digital electronic gyroscopes and acceleration sensors to control balance and motion, depending on the user's center of gravity. The Axle also uses a control system to drive the motors that are located within the wheels. The Axle has a built-in inertia dynamic stabilization system that can help assist with balance when moving forward and backwards, but not while turning. -
Page 8: Controls And Display
PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY TURNING YOUR DEVICE ON/OFF Power On: Take your Axle out of the box and place it flat on the floor. Press the power button (located on the rear of your Axle) once. Check the LED indicator (located in the center of your Axle). The battery indicator light should be lit, indicating the Axle is powered on. -
Page 9: Before Riding
BEFORE RIDING It is important that you fully understand all elements of your Axle. If these elements are not used correctly, you will not have full control of your Axle. Before you ride, learn the functions of the various mechanisms on your scooter. -
Page 10: Safety Precautions
Hover-1 is not liable for tickets or violations given to riders who do not follow local laws and regulations. • For your safety, always wear a helmet that meets CPSC or CE safety standards. - Page 11 • Do not operate the Axle when you are restless or sleepy. • Do not ride your Axle off of curbs, ramps, or attempt to operate in a skate park, empty pool, or in any way similar to a skateboard or scooter.
- Page 12 • Do not ride your Axle near motor vehicles or on public roads. • Do not travel up or down steep hills. • The Axle is intended for use by a single individual, DO NOT attempt to operate the Axle with two or more people.
- Page 13 • Do not attempt any stunts or tricks with your Axle. • Do not ride the Axle in dark or poorly lit areas. • Do not ride the Axle off road, near or over potholes, cracks or uneven pavement or surfaces.
- Page 14 Axle just as if you were standing on the ground. On average, it takes 3-5 minutes just to get comfortable standing on...
- Page 15 When you first begin using your Axle, the fastest way to move in your desired direction is to focus in that direction. You will notice that just...
- Page 16 Axle. Dismounting your Axle can be one of the easiest steps, yet when done incorrectly, may cause you to fall. To properly dismount, from a stopped position, lift one leg up and set your foot back down on the ground (STEPPING BACK).
-
Page 17: Balance & Calibration
If your Axle is unbalanced, vibrating, or not turning properly, you can follow the below steps to calibrate it. • First, place the Axle on a flat, horizontal surface such as the floor or a table. The foot mats should be even with each other and not tilted forward or backward. Make sure the charger is not plugged... -
Page 18: Safety Alerts
• Unsafe riding surfaces (uneven, too steep, unsafe, etc.) • When you step on the Axle, if the platform is tilted more than 10 degrees forward or backward. • Battery voltage is too low. - Page 19 • While sustaining a high discharge current during use (such as driving up a steep slope for a long period of time), the Axle engine will power off and stop after 15 seconds. WARNING When the Axle turns off during a Safety Alert, all operation systems will halt.
-
Page 20: Battery Care / Maintenance
• Do not connect or attach the Axle or the battery to a power supply plug or directly to a car’s cigarette lighter. • Do not place the Axle or batteries near a fire, or into direct sunlight. Heating the Axle and/or the battery can cause additional heating, breaking, or ignition of the battery inside the Axle. - Page 21 Use of any other charger or cable voids the manufacturer warranty. • Do not use your Axle if the battery begins to emit odor, overheats, or begins to leak. • Do not touch any leaking materials or breathe fumes emitted.
-
Page 22: Care And Maintenance
• Do not dispose of the Axle in fire as it may explode or combust. • Do not expose the Axle to contact with sharp objects as this will cause scratches and damage. -
Page 23: Warranty
WARRANTY For warranty information, Please visit us at: www.hover-1.com Affix Serial Number Label Here:... - Page 24 @RideHover1 @RideHover1 @RideHover1 www.Hover-1.com...