Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VIRTUFIT Etappe 2.0i Spinbike
Summary of Contents for VIRTUFIT Etappe 2.0i Spinbike
- Page 1 Etappe 2.0i Spinbike User manual...
- Page 2 11 - 12 ADJUSTMENTS GUIDE ADJUSTMENTS GUIDE MAINTENANCE MAINTENANCE TROUBLE SHOOTING TROUBLE SHOOTING 15 - 20 CONTROL PANEL CONTROL PANEL APPS APPS EXPLODED DRAWING EXPLODED DRAWING 23 - 24 PARTS LIST PARTS LIST TRAINING INSTRUCTIONS TRAINING INSTRUCTIONS Virtufit Etappe 2.0i Spinbike...
-
Page 3: Safety Instructions
– Ensure there are no children nearby when you are exercising on the device. In addition, the device should be showed in a place that children or house pets cannot reach. – Ensure that only one person at a time uses the fitness device. Virtufit Etappe 2.0i Spinbike... - Page 4 – Maintenance assembly and repair work not carried out by an official dealer. – In the event of improper use, neglect and / or poor maintenance. – Failure to maintain the fitness equipment in accordance with the manufacturer’s instructions (see the enclosed manual). Virtufit Etappe 2.0i Spinbike...
- Page 5 #10 Handlebar 1PC #15 Pedal 1pair #30 Rear Stabilizer Assembly 1PC #25 Front Stabilizer Assembly 1PC #37 Ipad holder 1PC (Optional) Bilster Card 1PC #34 Saddle 1PC #102 Adaptor 1PC #108 aluminum bottle holder 1PC #28 Mainframe 1PC Virtufit Etappe 2.0i Spinbike...
- Page 6 CHECKLIST TOOLKIT When you open the carton, and you will find the below parts in the carton: Virtufit Etappe 2.0i Spinbike...
- Page 7 Remove the steel tube and attachment parts from the main frame before attaching the front and rear stabilizer. Make sure the transport wheels on the front stabilizer are pointing forward. Attach the stabilizers to the main frame. Virtufit Etappe 2.0i Spinbike...
- Page 8 (a) and (b) do not fall into the tube. Align the clips on the cable connectors and make sure the connectors are locked in place. Do not shorten the cable. • Attach the console rod (7) first and then the handlebars (10). Make sure the direction of the handlebar (10) is correct. Virtufit Etappe 2.0i Spinbike...
- Page 9 WHITE BLUE • Before attaching the screen, connect the cables and do not shorten the cables. Push the extra wire down into the back of the screen after it is connected. Install the screen. Virtufit Etappe 2.0i Spinbike...
- Page 10 ASSEMBLY INSTRUCTIONS STEP 4 • Attach the saddle to the seat post. Secure the saddle firmly with the multi-purpose wrench. Virtufit Etappe 2.0i Spinbike...
- Page 11 If you tighten the left pedal clockwise, there is a chance that you may that you damage the screw thread of the pedal and the pedal can no longer be put on. the pedal can no longer be mounted. Virtufit Etappe 2.0i Spinbike...
- Page 12 Do not use until the unit is fully assembled and inspected for proper function and inspected for proper operation in accordance with the User Manual. NOTE! Turn off the power source when not using the unit for a long period of time. Virtufit Etappe 2.0i Spinbike...
-
Page 13: Adjustments Guide
2. Adjust the height of the handle so that the lowest part of the handle is the same height as the seat cushion. As shown in Figure 5. 3. Adjust the front and rear position of the seat cushion. When the foot is at the forefront, your knee just exceeds your foot, as shown in Figure 6. Virtufit Etappe 2.0i Spinbike... - Page 14 If you do need to adjust the spinning bike slightly, with a simple twist of the adjustable ends of both sides of the frame, you can compensate the spinning bike with the uneven ground. ten the locking nuts. Virtufit Etappe 2.0i Spinbike...
- Page 15 2. Second find the hole on the bottom of the chain cover. And then Insert the slotted screwdriver into the hole. 3. Please hold the handlebar of the slotted screw driver and meanwhile pull the plate open slightly. 4. At last remove all of the screws by cross screwdriver. Virtufit Etappe 2.0i Spinbike...
- Page 16 HAND PULSE SENSORS Hand pulse sensors This VirtuFit fitness equipment is provided with hand pulse sensors for measuring the heart rate. The hand pulse sensors are located on the handlebars. The hand pulse sensors are only working if they are touched both at the same time for a couple of seconds.
- Page 17 (health) of the person using the machine. • Always be aware of how you feel when you exercise. If you feel dizzy or lightheaded, stop immediately and rest. If you don’t work up a sweat, pick up the pace! Virtufit Etappe 2.0i Spinbike...
-
Page 18: Daily Maintenance
The upright is secured with Allen screws, make sure that the bolts are tight at all times. If the bolts are not tight enough anymore, this can cause cracking. • If a main switch is attached to the appliance (on/off ), it should always be used after use be turned off. For more information, visit https://virtufit.nl/service/faq/ Virtufit Etappe 2.0i Spinbike... -
Page 19: Troubleshooting
The sensor cables that run from the heart rate sensor to the display are not properly installed or have become detached during use. • The sensors may become damp, dirty or greasy. So you have to clean them regularly. Virtufit Etappe 2.0i Spinbike... -
Page 20: Error Codes
• This screen must be equipped with a 9V/1A power adapter. When the screen displays abnormally display, unplug and plug it back in. • Without any operation, the console will go into standby mode after five minutes. Virtufit Etappe 2.0i Spinbike... -
Page 21: Control Panel
Confirm value. During Stop mode, toggle each setting item. ST./SP. Start/Stop. Press “ST./ST. ” to stop or start the workout. +/- FRONT Increase or decrease front gear (on handlebars left). +/- REAR Increase or decrease rear gear (on handlebars on the right). Virtufit Etappe 2.0i Spinbike... - Page 22 6. If a time, distance or calories has been set, this item will be displayed in the training state as a countdown. When the countdown reaches 0, the exercise will automatically stop with a “DI DI” sound. 7. In the exercise state, press the <ST./SP.> key to stop the device. Virtufit Etappe 2.0i Spinbike...
- Page 23 4. After pressing the <ST./SP.> key for 8 seconds to start the test, the display shows BMI-body mass index, FAT%-body fat percentage, and BMR-basal metabolic rate. NOTE! Before the test, press the heart rate sensor and keep the heart rate normal in the continuous Virtufit Etappe 2.0i Spinbike...
- Page 24 4. If a time, distance or calories has been set, this item will be displayed in the training state as a countdown. When the countdown reaches 0, the workout will automatically stop with a “DI DI” sound. Virtufit Etappe 2.0i Spinbike...
- Page 25 3. When the TIME display counts down to “0: 00”, the main display window shows F1 ~ F6, which indicates the level of heart rate recovery. It is recommended to test the heart rate value within the Virtufit Etappe 2.0i Spinbike...
- Page 26 6. Click the “Stop” button to end the exercise and upload the information. NOTE! If a crash occurs after connecting to the APP, please reconnect, or press the RESET button on the display to recover and reconnect. Virtufit Etappe 2.0i Spinbike...
-
Page 27: App Instructions
GOOGLE PLAY USER MANUAL FITSHOW FITSHOW FITSHOW VirtuFit does not provide service for third-party fitness apps such as Kinomap, iConsole, FitShow etc.. If you encounter any troubles with a third-party fitness app, please contact the app developer. Virtufit Etappe 2.0i Spinbike... -
Page 28: Exploded Drawing
EXPLODED DRAWING Virtufit Etappe 2.0i Spinbike... - Page 29 EXPLODED DRAWING 63 62 Virtufit Etappe 2.0i Spinbike...
-
Page 30: Parts List
Saddle post top right cover Nut M8*H5.5*S14 56 Nylon nut M10*H9.5*S17 1 Adjustable leveling knob 57 Free wheel shaft 1 Mainframe 58 Corrugated washer d12*Φ15.5*0.3 1 Square neck bolt M8*90*20*H5 59 Bearing 2 Rear stabilizer 60 Free wheel 1 Virtufit Etappe 2.0i Spinbike... - Page 31 D-shaped bush B Multi-function wrench S13-14-15 85 Right handlebar post cover 1 C Allen wrench S5 86 Cross countersunk screwsM5*18*φ8 1 87 Locking block 2 88 Rubber band 1 89 Bottom slider 1 90 Saddle seat 1 Virtufit Etappe 2.0i Spinbike...
-
Page 32: Training Instructions
The purpose of cooling down is to return the body to its normal or near normal, resting state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to return to the heart. Virtufit Etappe 2.0i Spinbike... - Page 33 For questions or missing parts please contact your dealer.
Need help?
Do you have a question about the Etappe 2.0i Spinbike and is the answer not in the manual?
Questions and answers