Makita UM110D Instruction Manual page 16

3. Adjust the three pins so that they are lined up on
the alignment line.
► Fig.15: 1. Alignment line
4.
Apply a small amount of grease to the periphery
of the crank. Attach the crank to the pins with the small
and large rounds facing up.
► Fig.16: 1. Crank
5. Adjust the blades and guide plate so that the hole in the
guide plate and the two protrusions on the blades are lined up.
► Fig.17: 1. Guide plate
6.
Turn the shear blades upside down and install
them so that the pins on the tool fit in the hole on the
guide plate. Make sure that the shear blades are fixed
securely in place.
► Fig.18: 1. Guide plate
NOTE: Sliding the blade cover forward slightly makes
it easier to install the shear blades.
7. Place the undercover so that
cover is aligned with
► Fig.19: 1. Undercover 2. Lock lever
8. While pressing the undercover, turn the under-
cover clockwise until
with on the lock lever.
► Fig.20: 1. Undercover 2. Lock lever
9. Make sure that the lock lever fits in the groove on
the undercover.
► Fig.21: 1. Lock lever
CAUTION:
Never use the tool without install-
ing the undercover.
10. Remove the blade cover, and then turn on the tool
to check that it works properly.
NOTICE:
If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing shear blades
for hedge trimmer
CAUTION:
Attach the blade cover before
removing or installing the shear blades.
NOTICE:
If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
Removing shear blades
1.
Place the tool upside down.
► Fig.22
2. While pressing the lock lever, turn the undercover
counterclockwise until
with on the lock lever.
► Fig.23: 1. Lock lever 2. Undercover
3. Remove the undercover.
► Fig.24: 1. Undercover
on the under-
on the lock lever.
on the undercover is aligned
on the undercover is aligned
4. Loosen two screws with a screwdriver and remove
the shear blades.
► Fig.25: 1. Screws
NOTE: The shear blades can be removed without
removing the screws.
5. Remove the crank from the shear blades.
► Fig.26: 1. Crank
NOTE: The crank may remain in the tool.
NOTE: Attach the blade cover and the storage case to
the removed shear blades, and then store the blades.
Installing shear blades
1. Prepare the crank, undercover, and new shear
blades.
► Fig.27: 1. Crank 2. Undercover 3. Shear blades
2. Attach the blade cover to the shear blades.
► Fig.28: 1. Blade cover
3.
Adjust the three pins so that they are lined up on
the alignment line.
► Fig.29: 1. Alignment line
4. Apply a small amount of grease to the periphery of
the crank. Attach the crank to the pins with its small and
large rounds facing down.
► Fig.30: 1. Crank
5.
Slide the shear blades so that the hole on the guide
plate is positioned at the center of the rings of blades.
► Fig.31: 1. Guide plate
6. Turn the shear blades upside down and install them so
that the pin on the tool fits in the hole on the shear blades.
Insert the claw of the guide plate into the groove on the tool.
Make sure that the shear blades are fixed securely in place.
► Fig.32: 1. Claw 2. Guide plate
NOTE: Sliding the blade cover forward slightly makes
it easier to install the shear blades.
7.
Tighten the two screws firmly with a screwdriver.
► Fig.33: 1. Screws
8.
Place the undercover so that
cover is aligned with
► Fig.34: 1. Lock lever 2. Undercover
9. While pressing the undercover, turn the under-
cover clockwise until
with on the lock lever.
► Fig.35: 1. Undercover
10. Make sure that the lock lever fits in the groove on
the undercover.
► Fig.36: 1. Lock lever
CAUTION:
Never use the tool without install-
ing the undercover.
11. Remove the blade cover, and then turn on the tool
to check if the tool works properly.
NOTICE:
If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
16 ENGLISH
on the under-
on the lock lever.
on the undercover is aligned