Advertisement
Quick Links
m
Effective cutting width
100 mm
14")
100 mm (4")
MODEL UMlOOOD
100 mm (4")
MODEL UMlOOODW
With Fast Charger
Net
weight
1 k g 12
2
lbsl
Strokes per
min
1,000
Dimensions
IL
x
W
x
HI
320
mm
x
100
mm x 108
mm
112-5/8"
x
4" x 4 114")
INSTRUCTION MANUAL
Battery Cartridge 7000
Voltage
Charging
time
7 2 v
1
Hr
SPEC IF
I
CAT IONS
Model UMlOOOD
*
Model DC7100 Fast Charger
input
output
A.C
only
50
H r
~
6 0 H r
D C 7 2 V
x
Manufacturer reserves t h e right t o change specifications w i t h o u t notice
*
Note: Specifications m a y differ f r o m c o u n t r y t o country.
Advertisement
Related Manuals for Makita UMLOOOD
Summary of Contents for Makita UMLOOOD
- Page 1 INSTRUCTION MANUAL SPEC IF CAT IONS Model UMlOOOD Strokes per Effective cutting width 100 mm 14") Battery Cartridge 7000 Voltage Charging 7 2 v Manufacturer reserves t h e right t o change specifications w i t h o u t notice Note: Specifications m a y differ f r o m c o u n t r y t o country.
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. Be aware that this appliance is always in an operating condition, because it does not have t o be plugged into an electrical outlet. - Page 3 Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow.
- Page 4 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 4OoC or ABOVE (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. not allow anything t o cover Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material.
- Page 5 Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out plate on the bottom of the tool and grasp both sides of the cartridge while withdrawing from the barrel.
- Page 6 Switch action To prevent the trigger from being acciden- tally pulled, a lock-off lever i s provided a safety feature. To start the tool, slide the lock-off lever in the direction of the arrow and pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns...
- Page 7 When trimming twigs and foliage, do not attempt to trim too much time. Pro- a t a ceed gently. do not attempt Also, thick branches. NOTE : You can expect up to 45 minutes running time on a single charge.
-
Page 8: Maintenance
MAINTENANCE CAUTION : Always be sure that the tool i s switched off and the battery cartridge is removed before attempting t o perform inspection or maintenance. maintenance Blade I f the blades become dull or slightly dam- aged by contact with foreign matter, they can usually be restored to their original performance by sharpening with a file. - Page 9 Do not remove the grease on the gears or gear housing when replacing the blades. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance of adjustment should be performed by Makita Authorized or Factory Service Centers, using Makita replacement parts.
- Page 10 ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories attachments should be used only in the proper and intended manner.
- Page 11 Mar -10-'87 (4") 100 mm CORDLESS GRASS SHEAR Model UMIOOOD Note: The switch and other part configurations may differ from country to country.
- Page 12 Note The switch and other part specificat~ons may differ MAKIIA LlMmED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.