1. Manuals
  2. Brands
  3. Sno-Way Manuals
  4. Control Systems
  5. ProControl 2 Plus
  6. Installation & owner's manual

Sno-Way PROCONTROL 2 PLUS Installation & Owner's Manual

Wireless operating system package with energy smart system
Hide thumbs Also See for PROCONTROL 2 PLUS:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION &
OWNER'S MANUAL
PROCONTROL 2 PLUS™ WIRELESS
OPERATING SYSTEM PACKAGE WITH
ENERGY SMART SYSTEM
99101398
HIN
MERK: Norsk begynner på side 33
®,
®
®
Sno-Way
Down Pressure
and EIS
are registered trademarks of Sno-Way International, Inc.
™
™
™
™
™
™
ProControl
, V-Wing
, E-Z Switch
, Revolution
, MaxAdjust
, and SpeedLock
, are trademarks
of Sno-Way International, Inc.
®
©2020 Sno-Way
International
97102222A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PROCONTROL 2 PLUS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sno-Way PROCONTROL 2 PLUS

Summary of Contents for Sno-Way PROCONTROL 2 PLUS

  • Page 1 OPERATING SYSTEM PACKAGE WITH ENERGY SMART SYSTEM 99101398 MERK: Norsk begynner på side 33 ®, ® ® Sno-Way Down Pressure and EIS are registered trademarks of Sno-Way International, Inc. ™ ™ ™ ™ ™ ™ ProControl , V-Wing , E-Z Switch...

  • Page 2: Table Of Contents

    Common Macro Programming ..............12 Operation of Snow Plow Lights Using The Energy Smart System with ProControl 2 Plus™ (For Vehicles that don't use a Snow Plow Interface Module Kit) ....................... 12 Operation of Snow Plow Lights Using The Energy Smart System with ProControl 2 Plus™...

  • Page 3: Introduction

    BE AWARE! It is illegal to remove, deface or other- This manual was written for the assembly, installation and maintenance of your new Sno-Way ProControl 2 Plus™ wise alter the safety decals mounted on this equip- Operating System. Most importantly, this manual provides ment.

  • Page 4: Safety

    ALWAYS check surrounding area for hazardous decals are in place and are legible before operation obstacles before operating this unit. begins. New decals can be obtained from Sno-Way or ALWAYS inspect the unit periodically for defects. Parts your local dealer.

  • Page 5: Installation

    INSTALLATION 4. Re-install the cap screw and nylock nut previously Receiver Installation on Plow Power Pack removed. 1. Remove the pump cover. 5. Connect the 14 pin connector on the receiver module to the snow plow power pack. For non-straight blade 2.

  • Page 6: Cubic Foot Spreader

    3. Slide the receiver into the bracket with the 6-Pin in 4. Plug the spreader spinner motor harness and vibrator circuit programing pins located vertically in the open end harness (optional) into the mating plugs on the receiver of the bracket. Secure the receiver with a ¼" x 6" hex (See Figure 1-6).

  • Page 7: Control Harness Installation On Salt Spreader

    NOTE: In the next step, if the Power Harness does not Control Harness Installation On Salt have the ring terminals crimped on, any excess harness Spreader length that isn't needed to reach the battery, can be cut off. Then, the ring terminals that are bagged separately onto the harness can be crimped onto the red and black Power Harness wires of the harness.Crimp the smaller ring terminal on...

  • Page 8: Pairing Receiver And Transmitter

    2. Turn the ProControl 2 Plus™ transmitter on, and put it into Pairing Mode by pressing and holding the Down pressure button or pairing button for at least 5 seconds, but not more than 10 seconds. When the button is released, the backlights will flash continuously and the transmitter will be in pairing mode.

  • Page 9: Operation

    1. The center button just above the joystick (Figure 1- 3. The third key part of the ProControl 2 Plus™ is its 10, A) is the power button. Press and hold the power operation with the Energy Smart System (ESS), a button for three seconds to turn on the control.

  • Page 10: Basic Functions: V-Wing™ And Revolution™ Plows

    3. Pushing the joystick left will cause the plow to do a Basic Functions: “Left” function. Pushing the joystick right will cause the V-Wing™ and Revolution™ Plows plow to do a “Right” function. 4. The button just below the joystick (Figure 1-11, C) is 1.

  • Page 11: Basic Functions: Salt Spreaders

    Pushing and releasing the button will raise the spinner one speed step. There are a The top row of buttons on the ProControl 2 Plus™ total of four speed steps available. transmitter are used to control a Sno-Way tailgate spreader.

  • Page 12: Common Macro Programming

    4. Press the macro button for the macro you are 1. When the red/white (Daytime Run Light Sense) wire programing to exit learning mode. senses the vehicle's DRL is powered, the marker lights on the plow turn on. 5. Test macro by pushing the macro button for the macro just created.

  • Page 13: Operation Of Snow Plow Lights Using The Energy Smart System With Procontrol 2 Plus™ (For Vehicles That Use A Snow Plow Interface Module Kit)

    ALTERNATELY WITH WITH SPREADER BACK LIGHT 4 TIMES RECEIVER The ProControl 2 Plus™ transmitter uses a very small amount of electrical current anytime it is’ On’. To minimize current use when the ProControl 2 Plus™ transmitter is PLOW RECEIVER inactive, the system has a ’Sleep’ mode to shut itself LIGHT down.

  • Page 14: Procontrol 2 Plus™ Transmitter Mounting Instructions

    Using the ProControl 2 Plus™ to Aid in Mounting and Removing the Snow Plow VEHICLE RECEIVER LIGHT The ProControl 2 Plus™ transmitter can be used near the DESCRIPTION INDICATION snow plow when mounting or removing the plow with the aid of the power jackstand.
  • Page 15 NOTES...
  • Page 16 ® SNO-WAY INTERNATIONAL, INC. Hartford, WI 53027 USA Website: www.snoway.com © ® 2020 Sno-Way International...

This manual is also suitable for:

99101398

Table of Contents

Save PDF