Table of Contents
Advertisement
Stay alert! Give your work undivided attention. Use common sense. Do
not operate the machine under the influence of drugs, alcohol or any
medication.
Keep children and visitors a safe distance from the work area. Never
leave a running machine unattended. Before you leave the workplace
switch off the machine.
Do not use the machine in a dump environment and do not expose it to
rain.
Focus on the position of your fingers and other parts of your body when
working. Do not start the machine without safety appliances.
Machine only stock which rests securely on the table.
Do not remove chips and workpiece parts until the machine is at a
standstill.
Clamp the workpiece only when the machine is switched off. Rotate the
workpiece by hand before starting the machine. Rough out the workpiece
before installing it on the faceplate.
Do not stand on the machine.
Use a suitable power cord that can handle the machine's power input.
Connection and repair work on the electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord replaced immediately.
Make all machine adjustments or maintenance with the machine
unplugged from the power source.
3.3 Hazards
When using the machine according to regulations some remaining
hazards may still exist.
Thrown workpieces and workpiece parts can lead to injury.
Only process selected woods without defects.
Dust and noise can be health hazards.
Be sure to wear safety goggles, ear protection and dust mask.
Do not use damaged or worn power cord.
3.4 Grounding Instructions
Connection cord:
In case of a defect or malfunction, grounding provides a path of least
resistance to electric current, reducing the risk of electric shock. The
machine is supplied with connection cord with a guard wire and euro plug.
The plug must only be connected to an appropriate outlet in accordance
with all local codes and regulations.
• Do not modify the plug, if it does not fit into the socket. Contact a
qualified electrician and have the appropriate socket installed.
• Improper connection may result in a risk of electric shock. Ground wire
is an insulated wire with a green surface with/without yellow stripes. If the
cord or plug needs to be repaired, contact a qualified electrician.
• Damaged cords should be repaired immediately and only by a
qualified electrician.
• Use only three-wire cables with a euro plug and an appropriate socket.
3.5 Woodturning Lathe
Woodturning lathes are typically used to shape wood into cylindrical
profiles. Objects made on a wood lathe include items such as furniture
legs, lamp posts, baseball bats, bowls and other ornamental forms. Wood
lathe tooling consists of fixturing and securing devices for the workpiece,
a moveable toolrest and hand-held cutting tools in the form of long
handled gouges, skews, scrapers and parting tools. Specialty tooling is
also available for internal shaping and surface development.
Electrical supply conditions - info for electricians
Voltage: Steady state voltage: 0,9 to 1,1 of nominal voltage.
Frequency: 0,99 to 1,01 of nominal frequency continuously; 0,98 to 1,02
short time.
Harmonics: Harmonic distortion not exceeding 10 % of the total r.m.s.
voltage between live conductors for the sum of the 2nd through to
the 5th harmonic. An additional 2 % of the total r.m.s voltage between
www.igmtools.com
live conductors for the sum of the 6th through to the 30th harmonic is
permissible.
Voltage unbalance: Neither the voltage of the negative sequence
component nor the voltage of the zero sequence component in three-
phase supplies exceeding 2 % of the positive sequence component.
Voltage interruption: Supply interrupted or at zero voltage for not more
than 3ms at any random time in the supply cycle with more than 1s
between successive interruptions.
Voltage dips: Voltage dips not exceeding 20 % of the peak voltage of the
supply for more than one cycle with more than 1s between successive
dips.
Physical environment and operating conditions
Ambient air temperature: between 5° C to 40° C
Humidity: The relative humidity does not exceed 50 % at a maximum
temperature of 40° C.
Altitude: Up to 1000 m MSL.
Transportation and storage: Within a range of -25°C to 55° C and for short
periods not exceeding 24 hours up to 70° C.
Locking the lathe
Fig. 1: Method of locking Laguna Revo lathe. (1) Constructed 3 side
box with padlock holes. (2) Padlocks.
It is strongly recommended that the lathe is never left unattended in the
unlocked condition. To lock the machine it is recommended that a cover
(not supplied) is constructed.
4. Machine Specification
Motor specification
Power:
Power output:
Current at maximum load 2,5 A
Recommended circuit breaker
Dimensions
Package dimensions (LxWxH):
Package weight:
Length x width x height:
Weight:
Floor to bed height (no pads):
Floor to Spindle Centre height (no pads):
Bed length:
Toolrest length:
Toolrest post diameter:
Faceplate diameter:
Lathe Specification
High Speed Range:
Mid Speed Range:
Low Speed Range:
Distance between Centres:
Swing over Bed:
Swing over Banjo:
Spindle Bore:
Spindle / Tailstock Taper:
Spindle Thread:
-4-
Fig. 1
230V / 50 Hz / 1 phase
0,75 kW, S1
(S1 - Permanent load)
16 A, tripping
rating C (16/1/C)
920 mm x 380 mm x 520 mm
750 mm x 226 mm x 442 mm
328,75 mm
746,8 mm
203,2 mm
950 - 3500 RPM
450 - 1750 RPM
100 - 525 RPM
MK2 / MK2
M33 x 3,5 mm
61 kg
56,3 kg
170 mm
25,4 mm
76,2 mm
390 mm
310 mm
241 mm
9,5 mm
Advertisement
Table of Contents
