Page 1
Installation and operating instructions PROFESSIONAL COOKER WITH OVEN CF4-8ET CF4-8ETS CFC4-8ET CF4-8G CF4-8GEM CF4-8GEMS Model LIBR.ISTR.CF4-8 Code 563002901 Review 1 Edition date 20/05/2019 Language English LOTUS S.p.A. Via Calmaor, 46 31020 San Vendemiano +39 0438 778020 +39 0438 778277 Translation of the original instructions...
Contents Contents INTRODUCTION ......................... Installation drawing ........................Components..........................GENERAL INFORMATION......................Declaration of compliance......................User information, RAEE Directive on waste electrical and electronic equipment ......Technical data table ........................INSTALLATION........................... Delivery checks ..........................Removing the packaging ......................Mechanical installation ......................... Electrical/gas connections ......................BURNERS TECHNICAL DATA TABLE (ITGB)................
Page 3
Contents Spare parts ..........................CLEANING..........................Routine cleaning .......................... Cleaning the glass ........................Translation of the original instructions...
Page 4
Contents Translation of the original instructions...
INTRODUCTION 1 INTRODUCTION Installation drawing FIG. 1 CF4-8.. A Data Plate B Electrical connection C Gas connection Translation of the original instructions...
INTRODUCTION Components FIG. B 1 Gas ring cover 2 Injector 3 Air adjustment 4 Knob 5 By-pass 6 Gas tap 7 Ramp 8 Ignition button Translation of the original instructions...
Page 7
INTRODUCTION FIG. C Air adjustment FIG. E 1 By-pass Translation of the original instructions...
Page 8
INTRODUCTION FIG. D 1 Ignition spark plug 2 Injector 3 Extends drainage 4 Air adjustment Translation of the original instructions...
Page 9
INTRODUCTION TOP WIRING DIAGRAM CF4-8ET... 1 Switch 2 White indicator light 3 Power supply terminal board 4 Heating element Translation of the original instructions...
Page 10
INTRODUCTION TOP WIRING DIAGRAM CFC4-8ET 1 Power supply terminal board 2-3 Power regulator 4-5 Electrical plate 6 White indicator light 7 Residual heat indicator light Translation of the original instructions...
Page 11
INTRODUCTION STATIC ELECTRIC OVEN WIRING DIAGRAM (D) 1 Switch 2 Oven lamp 3 Power supply terminal board 4 RS Upper resistor 4 RG Grill resistor 4 RI Lower resistor 5 White indicator light 6 Green indicator light 7 Timer 8 Thermostat Translation of the original instructions...
Page 12
INTRODUCTION WIRING DIAGRAM MULTIFUNCTION ELECTRIC OVEN (E) 1 Switch 2 Oven lamp 3 Power supply terminal board 4 Motor fan 5 RS Upper resistor 5 RG Grill resistor 5 RI Lower resistor 5 RC Circular resistance 6 White indicator light 7 Green indicator light 8 Timer 9 Thermostat...
Page 13
INTRODUCTION TOP WIRING DIAGRAM 1 Power supply terminal board 2 Push-button starting burner 3-4 Burner ignition control unit STATIC GAS OVEN WIRING DIAGRAM 1 Switch 2 Oven lamp 3 Power supply terminal board Translation of the original instructions...
GENERAL INFORMATION 2 GENERAL INFORMATION Declaration of compliance The manufacturer declares that the appliances comply with the requirements of the regulation GAR 2016/426 for the gas part and directive 2014/30/EU,2014/35/EU for the electrical part. Installation must be performed in compliance with current regulations, especially with regard to ventilation of the premises and the exhaust gas evacuation system.
Technical data table Electrical technical data table CF8E S65G MAXIMUM POWER SUPPLY MODEL DIMENSIONS POWER SUPPLY ABSORPTION OVEN LAMP (kW) CABLE silicon type CF4-8ET 80x65x87 400V~3N 50/60 Hz 17,4 0,015 5 x 2,5 mm² CF4-8ETS 80x65x87 400V~3N 50/60 Hz 17,4 0,015 5 x 2,5 mm²...
INSTALLATION 3 INSTALLATION Delivery checks On delivery, it is important to check the following: · External conditions of the packaging · The general status of the equipment · The conformity of the model with the information in the technical data plate and the instruction manual ·...
Page 17
INSTALLATION Warning Installation operations, any conversion to other types of gas and start-up must only be performed by qualified personnel, in accordance with current regulations. Gas systems, electrical connections and premises where the appliances are installed must comply with current regulations in the country of installation;...
Page 18
INSTALLATION valve and fast-closing valve. Once installation is complete, make sure that there are no gas leaks from the fittings; to do this, do not use a naked flame but substances that do not cause corrosion, such as solutions of soapy water or leak detectors.
Page 19
INSTALLATION - "A" type devices (see data plate) "A" type appliances must discharge combustion products into appropriate hoods, or similar devices, connected to an efficient fume stack or directly to the outside. (Natural evacuation) Fig. 1 If this is not possible, using an air suction device connected directly to the outside is permitted (Forced Evacuation) Fig.2, having a flow capacity not lower than the value defined in point 4.3 of the UNI-CIG 8723 standard.
Page 20
INSTALLATION 1 Windproof fume stack (fig.3) - Extractor hood (fig.4) 2 Servo system "B11" type appliances are supplied on request with a hood or a hood and windproof fume stack to be assembled and delivered separately. Translation of the original instructions...
INSTRUCTIONS FOR USE 5 INSTRUCTIONS FOR USE General information This appliance must only be used for its expressly intended purpose for cooking or heating food. Any other use is considered improper. The appliance is also intended for industrial use and must only be used by personnel trained for use and aware of the risks that the hot element entails.
INSTRUCTIONS FOR USE On the front panel, a plate is indicated above the knob to which it corresponds, marked by the index · Turn on the switch located upstream of the appliance. Turn the control knob that corresponds to the plate from "O"...
INSTRUCTIONS FOR USE · The single circuit plates, on the other hand, are operated simply by adjusting power from pos. 1 to pos. 6 Note · Each plate is connected to a power regulator, which makes it possible to select from among 6 ...
INSTRUCTIONS FOR USE Warning When the oven is operating, the door must be closed since otherwise the knobs and protective plates might overheat and be damaged MECHANICAL TIMER The cookers have an acoustic timer that can signal a maximum time of 120 minutes. Turn the knob to the right, position it to the preselected time, between 0 and 120 minutes (see figure);...
INSTRUCTIONS FOR USE Turn the control knob to the right and set the desired temperature. To switch off the oven, turn the knob to the right into position 0. When the oven is to be used with both heating elements under thermostat control, position the knob at the symbol .
Page 27
INSTRUCTIONS FOR USE The green pilot light comes ON, indicating that the oven is powered up. After selecting the type of cooking, turn the timer knob to the left into the manual position ("hand" symbol on the disk) or to the right, setting it on the required time between 0 and 120 minutes.
INSTRUCTIONS FOR USE 5.12 Cooking table for the fan oven Ventilated electrical oven cooking table Guide no. Temperature Min. cooking Type of food from the Quantity Kg °C time bottom Sweets With a beaten dough, in a mould With a beaten dough, without a mould 1-3-4 Shortcrust pastry, cake base 1-3-4...
INSTRUCTIONS FOR USE Note · The indication of use of the levels shown in the table is recommended when cooking on multiple levels · The indicated times refer to cooking on only one level. Add 5-10’ when cooking on multiple levels ·...
INSTRUCTIONS FOR USE Note The indication for using the levels given in the table is preferential when cooking on several levels. The times given refer to cooking on a single level; increase times by 5-10' if several levels are used. For the bone or rolled beef, veal, pork and turkey roasts, increase time by 20'.
MAINTENANCE 6 MAINTENANCE Routine When using the appliance over time, it is essential to perform regular maintenance to ensure safe operation. We therefore recommend stipulating a service contract. Caution Maintenance must only be performed by specialist personnel in compliance with current ...
MAINTENANCE Replacing the grill burner nozzle To replace the nozzle, unscrew the securing screws (see fig. D), move the burner to the right and release it, unscrew the nozzle (2) using a suitable wrench and replace it (see "Technical data" table). Set the air adjustment bush (4) to the corresponding value in the "technical data"...
Page 33
MAINTENANCE Spare parts It is possible to replace parts such as the gas tap, thermocouple, spark plug or the gas pipes simply and quickly. To replace such parts, proceed as follows: · GAS TAP: after disassembling the front panel, unscrew the gas connection screw couplings, remove the coupling, replace the faulty parts and install the new ones in sequence ...
Page 34
CLEANING 7 CLEANING Routine cleaning Caution The use of flammable fluids to clean the appliance is forbidden To ensure hygiene and the durability of the appliance, perform external cleaning on a regular basis, taking care not to damage the cables and the electrical connections. Before starting cleaning, disconnect the appliance from the power supply.