Seconique CORONA NEST OF TABLES Assembly Instructions Manual

Seconique CORONA NEST OF TABLES Assembly Instructions Manual

Hide thumbs Also See for CORONA NEST OF TABLES:

Advertisement

SEC/SW/05/21/MY1
CORONA NEST OF TABLES
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
FOR DOMESTIC USE ONLY
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
Page 01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CORONA NEST OF TABLES and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Seconique CORONA NEST OF TABLES

  • Page 1 SEC/SW/05/21/MY1 CORONA NEST OF TABLES ASSEMBLY INSTRUCTIONS IMPORTANT PLEASE READ BEFORE YOU CONTINUE FURTHER FOR DOMESTIC USE ONLY CARE AND MAINTENANCE After unpacking this product please keep the original packaging in case it needs to be returned for any reason.
  • Page 2: Parts List

    SEC/SW/05/21/MY1 2 02 2 02 * Use of power tools to assemble this product will invalidate any claim and damage this product making it unsafe !!! * Please assemble on a clean soft surface to avoid damage. * Please check carton contents and read the instructions before commencing assembly.
  • Page 3: Tools Required

    SEC/SW/05/21/MY1 FITTINGS FITTINGS Ø 3,5 x 35mm Ø 5 x 90mm GLUE Ø 8 x 30mm TOOLS REQUIRED Page 03...
  • Page 4: Hardware Required

    SEC/SW/05/21/MY1 STEP 1 PARTS REQUIRED FRONT/REAR PANEL (LARGE)(560mm) FRONT/REAR PANEL (MEDIUM)(420mm) FRONT/REAR PANEL (SMALL)(280mm) 2 02 HARDWARE REQUIRED Ø 8 x 30mm GLUE TOOLS REQUIRED Please assemble on Glue must be added to the a clean soft surface dowel holes on part to avoid damage.
  • Page 5 SEC/SW/05/21/MY1 STEP 3 PARTS REQUIRED FRONT/REAR PANEL (LARGE)(560mm) LEG NATURAL (LARGE) LEG GREEN (LARGE) HARDWARE REQUIRED Ø 5 x 90mm GLUE 2 02 TOOLS REQUIRED GREEN Please assemble on Glue must be added to the a clean soft surface dowel holes on part to avoid damage.
  • Page 6 SEC/SW/05/21/MY1 STEP 5 PARTS REQUIRED 01 - TOP PANEL (LARGE) HARDWARE REQUIRED Ø 3,5 x 35mm GLUE TOOLS REQUIRED Please assemble on Glue must be added to the a clean soft surface dowel holes on part to avoid damage. STEP 6 PARTS REQUIRED HARDWARE REQUIRED TOOLS REQUIRED...
  • Page 7 SEC/SW/05/21/MY1 STEP 7 PARTS REQUIRED FRONT/REAR PANEL (MEDIUM)(420mm) LEG NATURAL (MEDIUM) LEG GREEN (MEDIUM) HARDWARE REQUIRED Ø 5 x 90mm GLUE TOOLS REQUIRED 420mm GREEN Please assemble on Glue must be added to the a clean soft surface dowel holes on part to avoid damage.
  • Page 8 SEC/SW/05/21/MY1 STEP 9 PARTS REQUIRED 06 - TOP PANEL (MEDIUM) HARDWARE REQUIRED Ø 3,5 x 35mm GLUE TOOLS REQUIRED Please assemble on Glue must be added to the a clean soft surface dowel holes on part to avoid damage. STEP 10 PARTS REQUIRED HARDWARE REQUIRED TOOLS REQUIRED...
  • Page 9 SEC/SW/05/21/MY1 STEP 11 PARTS REQUIRED FRONT/REAR PANEL (SMALL)(280mm) LEG NATURAL (SMALL) LEG GREEN (SMALL) HARDWARE REQUIRED Ø 5 x 90mm GLUE TOOLS REQUIRED 280mm GREEN Please assemble on Glue must be added to the a clean soft surface dowel holes on part to avoid damage.
  • Page 10 SEC/SW/05/21/MY1 STEP 13 PARTS REQUIRED 11 - TOP PANEL (SMALL) HARDWARE REQUIRED Ø 3,5 x 35mm GLUE TOOLS REQUIRED Please assemble on Glue must be added to the a clean soft surface dowel holes on part to avoid damage. STEP 14 PARTS REQUIRED HARDWARE REQUIRED TOOLS REQUIRED...

Table of Contents