Advertisement
PolyGard
CO Transmitter
®
AT-1110_V3 – UserManual
AT-1110 V3 – UserManual
User Manual - AT-1110 V3
11 Notes and General Information
It is important to read this user manual thoroughly and clearly in order to understand the information and instructions.
The PolyGard
transmitter must be used within product specification capabilities. The appropriate operating and
®
maintenance instructions and recommendations must be followed. Due to on-going product development, INTEC
and MSR reserves the right to change specifications without notice.
The information contained herein is based upon data considered accurate. However, no guarantee is expressed or
implied regarding the accuracy of this data.
11.1 Intended Product Application
The PolyGard
transmitter is designed and manufactured for control applications and air quality compliance in
®
commercial buildings and manufacturing plants (i.e. detection and automatic exhaust fan control for automotive
maintenance facilities, enclosed parking garages, engine repair shops, warehouses with forklifts, fire stations,
tunnels, etc.).
11.2 Installers' Responsibilities
It is the installer's responsibility to ensure that all PolyGard
and local codes and OSHA requirements. Installation should be implemented only by technicians familiar with proper
installation techniques and with codes, standards and proper safety procedures for control installations and the latest
edition of the National Electrical Code (ANSI/NFPA70). It is also essential to follow strictly all instructions as provided
in the user manual.
11.3 Maintenance
It is recommended to check the PolyGard
deviations may easily be corrected. Re-calibration and part replacement in the field may be implemented by a
qualified technician and with the appropriate tools. Alternatively, the easily removable plug-in transmitter card with
the sensor may be returned for service to INTEC Controls.
11.4 Limited Warranty
MSR-Electronic-GmbH and INTEC Controls warrants the PolyGard
normal exposure for the sensor, from the date of shipment against defects in material or workmanship. Should any
evidence of defects in material or workmanship occur during the warranty period, INTEC Controls will repair or
replace the product at their own discretion, without charge.
This warranty does not apply to units that have been altered, had attempted repair, or been subject to abuse,
accidental or otherwise. The warranty also does not apply to units in which the sensor element has been overexposed
or gas poisoned. The above warranty is in lieu of all other express warranties, obligations or liabilities.
This warranty applies only to the PolyGard
or consequential damages arising out of or related to the use of the PolyGard
If the PolyGard® transmitter needs to be returned to INTEC Controls for service, an RMA number must be obtained
prior to sending.
Polygard® is a registered trademark of MSR
Customer Services (858) 578-7887 & (888) GO INTEC
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | relevantsolutions.com/inteccontrols
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | relevantsolutions.com/inteccontrols
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
Specifications subject to change without notice. | USA 160104 | Page 17 of 17
Specifications subject to change without notice. | USA 141114 | Page 17 of 17
®
transmitter regularly. Due to regular maintenance, any performance
®
transmitter. INTEC Controls or MSR shall not be liable for any incidental
®
PolyGard
Fax (858) 578-4633 & (888) FX INTEC
www.inteccontrols.com
Page 17
transmitter is installed in compliance with all national
transmitter for a period of two years, 12 months
®
transmitter.
®
is a registered trademark of MSR-Electronic GmbH | AT-1110V3
Polygard® is a registered trademark of MSR | AT-1110V3
®
Specification subject to change without notice.
AT-1110V3
Printed in USA 141114
Advertisement
