Notes And General Information; Intended Product Application; Installers' Responsibilities; Maintenance - Intec Controls MSR PolyGard AT-1195 V3 User Manual

PolyGard O Transmitter
®
2
AT-1195 V3 – UserManual
AT-1195_V3 – UserManual AT-1195 V3 – UserManual
User Manual - AT-1195 V3

11 Notes and General Information

It is important to read this user manual thoroughly and clearly in order to understand the information and
instructions. The PolyGard
operating and maintenance instructions and recommendations must be followed.
Due to on-going product development, MSR and INTEC Controls reserves the right to change specifications
without notice. The information contained herein is based upon data considered to be accurate. However, no
guarantee is expressed or implied regarding the accuracy of this data.

11.1 Intended Product Application

®
The PolyGard O transmitters are designed and manufactured for control applications and air quality compliance in
2
commercial buildings and manufacturing plants.

11.2 Installers' Responsibilities

It is the installer's responsibility to ensure that all PolyGard
and local codes and OSHA requirements. Installation should be implemented only by technicians familiar with
proper installation techniques and with codes, standards and proper safety procedures for control installations and
the latest edition of the National Electrical Code (ANSI/NFPA70). It is also essential to follow strictly all instructions
as provided in the user manual.

11.3 Maintenance

It is recommended to check the PolyGard
deviations may easily be corrected. Re-calibration and part replacement in the field may be implemented by a
qualified technician and with the appropriate tools. Alternatively, the easily removable plug-in transmitter card with
the sensor may be returned for service to

11.4 Limited Warranty

MSR-Electronic-GmbH and INTEC Controls warrants the PolyGard
12 months normal exposure for the sensor, from the date of shipment against defects in material or workmanship.
Should any evidence of defects in material or workmanship occur during the warranty period, INTEC Controls
will repair or replace the product at their own discretion, without charge.
This warranty does not apply to units that have been altered, had attempted repair, or been subject to abuse,
accidental or otherwise. The warranty also does not apply to units in which the sensor element has been
overexposed or gas poisoned. The above warranty is in lieu of all other express warranties, obligations or
liabilities.
This warranty applies only to the PolyGard
not be liable for any incidental or consequential damages arising out of or related to the use of the PolyGard
transmitter.
If the PolyGard transmitter needs to be returned to INTEC Controls for service, an RMA number must be
®
obtained prior to sending.
Polygard® is a registered trademark of MSR
Customer Services (858) 578-7887 & (888) GO INTEC
INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | relevantsolutions.com/inteccontrols 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | relevantsolutions.com/inteccontrols
INTEC Controls, 12700 Stowe Dr., Suite 110, Poway, CA 92064
Specifications subject to change without notice. | USA 160104 | Page 13 of 13 Specifications subject to change without notice. | USA 150109 | Page 13 of 13 Specifications subject to change without notice. | USA 200211 | Page 13 of 13
®
transmitters must be used within product specification capabilities. The appropriate
®
transmitter regularly. Due to regular maintenance any performance
INTEC Controls
transmitter. MSR-Electronic-GmbH and/or INTEC Controls shall
®
PolyGard
®
Fax (858) 578-4633 & (888) FX INTEC
®
transmitters are installed in compliance with all national
.
transmitter for a period of two years,
®
is a registered trademark of MSR-Electronic GmbH | AT-1195_V3_UserManual Polygard® is a registered trademark of MSR | AT-1195_V3_UserManual
Specification subject to change without notice.
www.inteccontrols.com
Page 13
®
AT-1195_V3_UserManual
Printed in USA 150109