TaBLE oF ConTEnTS Important Notices ����������������������������������������������������������������������������������������������������������������������������������������� 2 IR Transmit and Receive Modes M1 or M2) ����������������������������������������������������������������������������������� 3 Materials Included in this Package ����������������������������������������������������������������������������������������������������� 4 Removing and Installing Snap On Covers ������������������������������������������������������������������������������������� 5 General Vehicle Installation Approach ��������������������������������������������������������������������������������������������� 8 Connecting the Dome Lights ��������������������������������������������������������������������������������������������������������������11...
System adjustments can be accomplished using the remote control, while seat-belts remain fastened� Enjoy your AUDIOVOX entertainment system but remember that the safety of all passengers remains the number one priority�...
IR TRanSMIT anD RECEIVE MoDES (M1 oR M2) The AVXMTG10UA has an option that allows the user to select from two IR transmit and receive modes (M1 or M2)� This feature can be used when two AVXMTG10UA units are installed in the same vehicle or if the vehicle has an RSA (Rear Seat Audio) that uses “A” channel headphones� When in the M1 mode the unit will transmit audio on the A channel�...
*Note: The AVXMTG10UA is supplied with a black snap-on shroud and screen cover� To install the pewter or shale snap-on shroud or screen cover, the black snap-on shroud and screen cover must be removed first� See the following page for the removal process� 1� 10” LCD Overhead Monitor with DVD player 2� 12 Pin Power Harness 3�...
Place the unit on a soft surface to avoid damaging the plastic� Materials Required Shroud Screen Back Cab Pry Tool 10” Overhead LCD Monitor with DVD Player Disconnecting the Screen Cover “C” “B” “A” “C” 1� Open the LCD screen�...
Page 8
Installing the Screen Cover “D” “D” “D” “D” 1� Open the LCD screen� 2� Hook the two tabs “D” at the bottom edge of the screen cover into the notches on the bottom edge of the LCD screen� 3� Snap the opposite side of the screen cover over the hinges�� Disconnecting the Shroud “E”...
Page 9
Installing the Shroud “F” 1� Open the LCD screen� 2� Slide the shroud over the unit� The shroud will snap into place at locations “F”�...
2� If it is not certain how the dome lamps tie into the vehicle electrical system, wire the dome lamp circuit (of the DVD overhead) to the driver’s door pin switch� 3� Follow the instructions on pages 11-13� 4� Contact the Audiovox tech support line if you have any questions regarding dome lamp wiring�...
Page 11
GEnERaL VEhICLE InSTaLLaTIon aPPRoaCh CaUTIon: The 20mm and 40mm screws in the hardware kit are provided to facilitate installation� Use extreme caution when using these screws to avoid damage to vehicle roof or other components, wiring, etc� Installing Unit to Roof Roof Roof Support Headliner...
Page 12
GEnERaL VEhICLE InSTaLLaTIon aPPRoaCh Dome Light Power Source Line Out-L(White) Line Out-L(Red) Auxiliary Display Line Out-L(Yellow) 12 Pin Power Signal Harness Optional Relay FMDIRB AV IN 3 RCA Jack Pigtail...
ConnECTInG ThE DoME LIGhTS The dome lights in the video monitor require three connections to the vehicle’s wiring� There are two common types of dome light circuits used, positive or negative switched� Positive systems supply voltage to the interior lights to turn them on� Negative switched systems apply ground to illuminate the bulbs� To determine which system you have, you must locate the wires at the vehicle dome light�...
Page 14
Positive Switched Dome Lighting To 6 pin Red/black-Lamp on To 12 pin connector Black/red-Lamp common on Monitor Purple/brown-Lamp Auto constant +12 VDC Factory Door Ajar Switch or Body Control Computer constant +12 VDC * Connect to a vehicle ground...
Page 15
Negative Switched Dome Lighting Red/black-Lamp on To 12 pin To 6 pin Black/red-Lamp common connector Purple/brown-Lamp Auto Factory Door Ajar Switch or Body Control Computer constant +12 VDC constant * Connect to a vehicle ground +12 VDC...