Alvin WTB42 Assembly Instructions

Alvin WTB42 Assembly Instructions

Titan drafting tables
Hide thumbs Also See for WTB42:

Advertisement

B

Tools required:

Phillips screwdriver, awl, or drill with

Parts Included:

C
A
2pcs
Side Frames,
B
B
Left & Right
C

To Assemble Base Frame

Unpack and inspect contents to confirm
C
1
you have all the parts listed above. Use
care to differentiate rear crossbar (
(34½" long) from footrest crossbar (
(35½" long).
Attach both rear crossbars (
2
footrest and support crossbars (
A
one side frame (
) using 2" Allen bolts
H
(
). Tighten securely. Note: Threaded
barrels preattached to leg frames must
be in rear and facing out.
Attach other side frame (
3
ends of crossbars in step two using 2"
H
Allen bolts (
). Tighten securely.
D
Place dust cover (
) over top of base
4
frame and attach using ¾" Phillips
I
screws (
). Note: Wooden strip on dust
cover should be in front of table and
facing up.
Attach hinge assemblies (
5
frames into pre-drilled holes using
I
¾" Phillips screws (
) as shown in
diagram. Pay close attention to correct
orientation of left and right hinges.
Tighten securely.
Insert tilt adjustment rods (
6
threaded barrels on each side frame.
Titan Drafting Tables
Assembly Instructions
B
2pcs
Rear Crossbars
(34
" long)
7
8
Dust Cover w/ Drawer
G
2pcs
Hinge Assemblies,
Left & Right
B
)
C
)
B
) and the
C
) to
A
) to opposite
G
) to side
7
F
) into
8
C
B
" bit.
1
16
C
C
2pcs
B
B
Footrest & Support Crossbars
(35
" long)
7
8
D
1pc
C
C
H
16pcs
2" Allen Bolts
Screw adjustment knobs (
adjustment rods so that connecting brackets are about 2" above side frames
for the time being with rods facing straight up and down and rear mounting
brackets facing out, as shown in diagram. Tighten knobs securely.
Base frame assembly is now complete. Set aside.
DRAFTING HEIGHT
B
W/ DRAWER
For WTB42, WTB48, WTB60,
C
WTB42-WA, and WTB48-WA
B
B
C
C
E
2pcs
Adjustment Knobs
I
20pcs
¾" Phillips Screws
E
) into threaded barrels on each side frame. Set
F
2pcs
Tilt Adjustment Rods
J
1pc
Allen Wrench Key

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WTB42 and is the answer not in the manual?

Questions and answers

Summary of Contents for Alvin WTB42

  • Page 1 Tighten knobs securely. Base frame assembly is now complete. Set aside. DRAFTING HEIGHT W/ DRAWER For WTB42, WTB48, WTB60, WTB42-WA, and WTB48-WA 2pcs ⁄ " long)
  • Page 2 ¾" Phillips screws ( ). Tighten securely but use care not to over tighten and strip. ©2008 Alvin & CompAny, inC. • P.O. Box 188, Windsor, CT 06095-0722 Phone: 860-243-8991 • Toll-Free: 800-444-2584 • Fax: 860-242-8037 • Toll-Free Fax: 800-777-2896 19½"...

This manual is also suitable for:

Wtb42-waWtb48Wtb48-waWtb60

Table of Contents