Advertisement
This information makes the product easier to use.
•
Use the product correctly. Injury or death is a
possible result of incorrect use. Only use the product
for the tasks found in this manual. Do not use the
product for other tasks.
•
Read, understand and obey the instructions in this
manual. Obey the safety symbols and the safety
instructions. If the operator does not obey the
instructions and the symbols, injury, damage or
death is a possible result.
•
Do not discard this manual. Use the instructions to
assemble, to operate and to keep your product in
good condition. Use the instructions for correct
installation of attachments and accessories. Only
use approved attachments and accessories.
•
Do not use a damaged product. Obey the
maintenance schedule. Only do the maintenance
work that you find an instruction about in this
manual. An approved service center must do all
other maintenance work.
•
This manual cannot include all situations that can
occur when you use the product. Be careful and use
common sense. Do not operate the product or do
maintenance on the product if you are not sure about
the situation. Speak to a product expert, your dealer,
service agent or approved service center for
information.
•
Do not use the product if it is changed from its initial
specification. Do not change a part of the product
without approval from the manufacturer. Only use
parts that are approved by the manufacturer. Injury
or death is a possible result of incorrect
maintenance.
•
This product makes an electromagnetic field during
operation. The electromagnetic field can cause
damage to medical implants. Speak to your
physician and medical implant manufacturer before
you operate the product.
•
Do not let a child operate the product.
•
Do not let a person, without knowledge of the
instructions, operate the product.
•
Always monitor a person, with decreased physical
capacity or mental capacity, that uses the product. A
responsible adult must always be there.
•
Lock the product in an area that children and not
approved persons cannot access.
•
The product can eject objects and cause injuries.
Obey the safety instructions to decrease the risk of
injury or death.
•
Do not go away from the product while it is on. Stop
the product before you go.
•
Before and while walking rearward, look behind and
down for small children, animals or other risks that
can cause you to fall.
•
The operator of the product is responsible if an
accident occurs.
•
Make sure that parts are not damaged before you
use the product.
•
Refer to national or local laws. They can prevent or
decrease the operation of the product in some
conditions.
•
Know the controls and the correct operation of the
product before use.
•
Do not let children or persons without knowledge of
these instructions use the product.
•
Do not operate the product while persons, especially
children, or animals are near.
•
Keep children away from the area to be cut and
monitored by an adult.
•
Stop the product if children enter the work area.
•
Fully examine the area where the product is to be
used. Remove all objects which can be ejected by
the product during operation.
•
Examine the blade, blade bolt, blade assembly and
motor base before use for wear and damage.
•
Operate the product only in daylight or in good
artificial light.
•
Do not operate the product in wet grass.
•
Be careful near corners, bushes, trees or other
objects that can prevent your view.
•
Use very high caution when you reverse or pull the
product in your direction.
•
Do not put hands or feet near or below rotating parts.
Always keep clear of the discharge openings.
•
Stop the blade when you go across gravel surfaces.
•
Stop the motor, remove the battery pack and wait
until the blade stops fully before you clean the
product, remove the grass catcher or remove
material from the discharge chute.
•
Do not operate the product when you are tired, ill or
under the influence of alcohol or other drugs.
•
If the product has unusual vibration, stop the motor,
remove the battery pack and check immediately for
the cause. Vibration is usually a warning of damage.
•
Do not point ejected material in the direction of
others. Do not eject material against a wall or
blockage. Material may ricochet back in the direction
of the operator.
•
Do not operate the product without the correct
guards, plates, grass catcher or other safety
protective devices in position.
•
Remove branches, twigs, stones and other objects
from the lawn before you start to cut.
•
Keep persons, including children, and animals at a
safe distance from the work area.
•
Objects that hit against the cutting equipment can be
ejected and cause damage to persons and objects.
•
Do not use the product in bad weather, including fog,
rain, moist or wet locations, strong winds, intense
902 - 001 - 06.11.2018
5. Examine the blade support and blade bolt to see if
there is damage.
6. Examine the motor shaft to make sure that it is not
bent.
7. When you attach the new blade, point the angled
ends of the blade in the direction of the engine.
8. Make sure that the blade is aligned with the center of
the motor shaft.
The error codes help you do troubleshooting on the
product and/or the battery pack while in operation.
No LEDs come on after pressing
Battery pack not fully put
the power button on the user con-
into product or internal
trol interface, battery pack does not
fuse is blown
function in product
All four battery capacity LEDs
Battery pack not fully put
flash, no other LEDs come on after
into product or the internal
pressing the power button
temperature of the battery
pack is too hot or too cold.
All four battery capacity and power
Motor control handle held
LEDs flash, no other LEDs come
down when the power but-
on after pressing the power button
ton is pressed for the first
time or internal motor con-
trol handle switch failure
902 - 001 - 06.11.2018
9. Lock the blade with a block of wood. Attach the
spring washer and tighten the bolt and washer.
10. Pull the blade around by hand and make sure that it
turns freely.
Use heavy duty gloves. The
blade is very sharp and cuts can easily
occur.
11. Start the product to do a test of the blade. If the
blade is not correctly attached, there is vibration in
the product or the cutting result is unsatisfactory.
Push the battery pack fully into the powerhead un-
til a click is heard. If the LEDs do not illuminate af-
ter the battery pack has been fully put in and the
power button has been pressed on the user con-
trol interface, speak to an approved service cen-
ter.
Push the battery pack fully into the powerhead un-
til a click is heard. If the LEDs continue to flash,
the internal temperature of the battery pack may
be too low or too high. Allow the battery pack to
warm up or cool. To increase the cooling process,
the battery pack can be inserted into the battery
charger to actively cool the battery pack.
Release the motor control handle. If the motor
control handle is not held down and the LEDs
continue to flash, speak to an approved service
center.
Advertisement
