Related Manuals for Brunner Anliker XXL PRO
Summary of Contents for Brunner Anliker XXL PRO
- Page 1 Operating Manual Vegetable Cutter ANLIKER XXL PRO Translation of the German Original...
-
Page 2: Table Of Contents
Unpacking and installation ....................14 Consignment ........................14 Reporting Damage ......................14 Weight of the ANLIKER XXL PRO: ..................15 Transporting the ANLIKER XXL PRO vegetable cutter .............. 15 Assembly and installation ....................16 Electrical / electronic configuration ..................17 Start-up ..........................18 Storage .......................... - Page 3 Device transfer to third parties .................... 35 Technical Specifications ...................... 35 Warranty .......................... 35 Documents ........................36 9.6.1 Dimensional drawing ANLIKER XXL PRO ................... 36 9.6.2 CE Conformity Declaration ....................... 37 9.6.3 CE Conformity Declaration for accessories..................38 9.6.4 Supplement 1935/2004 ........................39...
- Page 4 Fig. 42: Wall-mounted cutting disc holder Fig. 43: Attaching the cutting disc holder to the holders on the machine. Fig. 44: Service opening Fig. 45: Dimensional drawing ANLIKER XXL PRO Fig. 46: CE Conformity Declaration Fig. 47: Conformity Declaration for accessories Fig.
-
Page 5: Anliker Xxl Pro - Introduction
1.1.2 Target group and mandatory reading The operating manual addresses all users of the ANLIKER XXL PRO vegetable cutter. Mandatory reading All users are to read section 2 “Safety”, page 7, before they start working with the ANLIKER XXL PRO vegetable cutter. Generated:... -
Page 6: Warnings And Instructions For Use
We use abbreviations and easy to recognize symbols at the page margins only for measuring units and the above mentioned warning and usage symbols. (Examples: see “Warnings and instructions for use”, page 6). In this manual, the ANLIKER XXL PRO vegetable cutter will also be referred to as the “device”. Manufacturer address Brunner-Anliker AG Brunnergässli 1 - 5... -
Page 7: Device Identification
ANLIKER XXL PRO vegetable cutter. Intended use The intended use of the ANLIKER XXL PRO vegetable cutter is the cutting and slicing of different types of vegetables in the catering and food processing industry. With the various cutting discs, the vegetables can be cut into different shapes and sizes. -
Page 8: General Safety Guidelines
Such jobs need to be executed by persons qualified accordingly. • All those working with the ANLIKER XXL PRO vegetable cutter must have been instructed on its use, read and understood the manufacturer’s operating manual. See also “User requirements”, page 8. -
Page 9: Structure
This chapter informs on the structure and accessories of the device. Structure of the basic unit The ANLIKER XXL PRO consists of a basic unit which rests on wheels, and a detachable top. Depending on the top, the device can be used for different jobs. -
Page 10: Structure With Filler Tray
Structure with filler tray The filler tray is mounted onto the holder piece of the basic unit Fig. 3: Tray attachment Item Item 1 Filler spout - tray 6 Plunger 2 Holder piece with inserted funnel 7 Plunger handle 3 Cutting disc holder 9 Outlet with cover (guard) 4 Power cable with holder 10 Fixed wheels... -
Page 11: Equipment
The customer can configure the device with different cutting discs, grating discs and dicing inserts. The basic unit always comes with funnel attachment, operating manual, cleaning brush and micro- fuses. Fig. 4: ANLIKER XXL PRO Fig. 5: Accessories kit? Fig. 6: Ejector Fig. -
Page 12: Accessories
Accessories The ANLIKER XXL PRO can be equipped with an optional PRO attachment. Supplementary accessories plus a large variety of cutting and grating discs as well as disc holders can be ordered from your sales partner or directly at our webshop. Please contact your distributor or visit our website for more information. -
Page 13: Materials
All housing parts and top are made of chromium steel. Control elements for activation and deactivation ANLIKER XXL PRO vegetable cutter operating concept: 1. Connect the device to the power outlet (“Electrical / electronic configuration”, page 16) and ensure that the EMERGENCY OFF pushbutton is unlocked (item 3 on page 9).. -
Page 14: Structure Of The Anliker L Vegetable Cutter
The ANLIKER XXL PRO vegetable cutter should not be lifted and transported by hand. If, however, manual lifting and transporting is inevitable, always work in two and lift the device at its holder rail. -
Page 15: Weight Of The Anliker Xxl Pro
Transporting the ANLIKER XXL PRO vegetable cutter The ANLIKER XXL PRO vegetable cutter stands on wheels and can be easily transported from one place to another. Remember to open the caster wheel brakes to relocate the vegetable cutter. At its new place of use, secure stability by snapping in the brake catches. -
Page 16: Assembly And Installation
Assembly and installation Ensure ergonomic work situations: Always place the device on a plane and solid surface with a minimum size of 800 mm x 1100 mm. Leave sufficient space around the vegetable cutter to swing open the funnel for the exchange of cutting discs, grating discs and dicing insert. -
Page 17: Electrical / Electronic Configuration
Electrical / electronic configuration The ANLIKER XXL PRO vegetable cutter comes with an approx. 4-meter power cable which can be plugged into a 230-Volt socket. To avoid tripping hazards, do not route the cable across passageways. HAZARD HAZARD! • Defective electrical components may be live and pose a life-threatening hazard. -
Page 18: Start-Up
• Ensure that there are no foreign bodies in the vegetable cutter’s filler spouts! HAZARD HAZARD! • Do not change or modify the ANLIKER XXL PRO vegetable cutter or add any equipment which might impair the safety or function of the device. Otherwise the device no longer complies with the CE standards. •... -
Page 19: Storage
Storage If the ANLIKER XXL PRO vegetable cutter is not used for a longer period of time, observe the following conditions to keep it fully functional: • The storage place must be dry and clean. • The ANLIKER XXL PRO vegetable cutter must not be exposed to extreme cold or heat. -
Page 20: Installation Of The Attachment
5 Installation of the attachment The ANLIKER XXL PRO vegetable cutter can be used for a myriad of jobs. Observe the following steps when inserting cutting discs, grating discs and dicing inserts: WARNING Cut injury due to sharp cutting faces •... -
Page 21: Fig. 17: Insert The Plunger
Inserting the plunger, fold up the safety latch. Fold down the safety latch when the plunger is completely inserted. Fig. 17: Insert the plunger Fig. 18: Safety latch Placing the filler tray in the holder piece: hold the tray in vertical position. The IN / OUT arrows facilitate the vertical alignment. -
Page 22: Correct Insertion Of The Cutting Discs, Grating Discs And Dicing Inserts
Fig. 23: Filler tray with attachment piece Correct insertion of the cutting discs, grating discs and dicing inserts 5.1.1 Preparation of the ANLIKER XXL PRO vegetable cutter for food processing Fold the filler tray up, open the locking lever and swing the attachment piece to the side. -
Page 23: Insertion Of Cutting Or Grating Disc
5.1.3 Insertion of cutting or grating disc Place the disc on the drive shaft. Turn the disc slightly until it engages with the pin on the drive shaft and sits correctly (observe upper flushness with the drive shaft). Correct cutting disc placement is possible only if disc hub and pin are absolutely clean. -
Page 24: Filler Tray With Attachment Piece
5.1.5 Filler tray with attachment piece The filler tray can now be closed on the attachment piece. If the turning filler neck is not used, it must be safely closed with the lid. Fig. 29: Ready for food processing Fig. 30: Lid on turning filler neck Fig. -
Page 25: Correct Disc Installation
Correct disc installation 5.2.1 Inserting the dicer grid The pin on the upper part must lock in the indent in the dicer grid. Fig. 32: Dicer grid indent Fig. 33: Upper part pin The dicer grid is in the correct position when the pin on the upper part locks in the dicer grid indent. -
Page 26: Brunoises Or Gaufettes
5.2.2 Brunoises or gaufettes Pay attention to the pins on the disc when brunoises or gaufettes discs are used. They must not get jammed during closure. Fig. 35: Pin Fig. 36: Pin on attachment piece If the attachment piece cannot be closed, rotate the disk slightly by hand until it is in the right position. -
Page 27: Cutting Vegetables
Cutting vegetables Put a suitable container (food container 1/1) or a large trolley container or tray under the processed food outlet. Switch on the device. Fill the filler spout with vegetables / fruit and push them down with the plunger. Fig. -
Page 28: System Care „Cleaning Concept
Removing the top Remove the attachment in reverse order to “Installation of the XXL PRO attachment piece” on page The first step is to separate the device from the power supply. -
Page 29: Cleaning The Cutting Discs, Grating Discs And Dicing Inserts (W)
Cleaning the cutting discs, grating discs and dicing inserts (W) Use the nylon brush included in the consignment to clean the cutting discs, the grating discs and the dicing inserts (dicing knives and dicer grid) under running water. Never clean the dicer grid with metal objects or by tapping it on the edge of a table. Best clean the grid by putting it in a combi steam oven at 90 degrees for about 10 minutes. - Page 30 Ensure that the device is switched off with the ON/OFF switch prior to any maintenance job. • Disconnect from the mains! • The ANLIKER XXL PRO vegetable cutter must not be cleaned with a stream-jet or high-pressure washers. • The use of aggressive cleaning agents is strictly prohibited. CAUTION CAUTION •...
-
Page 31: Mounting The Cutting Disc Holder
Mounting the cutting disc holder The cutting disc holder can accommodate up to seven different cutting discs. Its simple fastening principle allows it to be installed right were it is needed. Fig. 41: Cutting disc holder The disc holder can be easily taken off and moved to its new site of operation. -
Page 32: Troubleshooting
8 Troubleshooting The following chapter describes possible disturbances which might occur during operation, and their elimination. Elimination of malfunctions The machine is built to endure and therefore not very susceptible to malfunctions.. Action in case of malfunctions: First measure in case of malfunctions: Switch off the device! In case of unpleasant smells, unplug the mains plug. -
Page 33: Cutter Bar Broken
8.1.6 Cutter bar broken The cutter bars can break when they are no longer sharp or if they are collide with an object. IMPORTANT: Always search for the knife or its parts when broken. WARNING WARNING • High risk of injury for the customer/guest. •... -
Page 34: Annex
9 Annex Spare parts Spare parts must meet the technical requirements specified by the manufacturer. This compliance is guaranteed for original spare parts. Use original spare parts only. Our warranty is void if third-party parts or parts which have not been approved in writing are used. NOTE Note •... -
Page 35: Device Transfer To Third Parties
Device transfer to third parties All liabilities by Brunner-Anliker AG cease if the ANLIKER XXL PRO vegetable cutter is sold and transferred to a third party. Technical Specifications Machine type ANLIKER XXL PRO vegetable cutter Electrical connection 230 V 50/60Hz Electric motor 0.75 kW /... -
Page 36: Documents
Documents 9.6.1 Dimensional drawing ANLIKER XXL PRO Fig. 45: Dimensional drawing ANLIKER XXL PRO Generated: Reviewed: Revised: Status: 300 released Page 36 of 39 Ralph Moretti Document number: Index 28 Sept 2021 235.01551... -
Page 37: Ce Conformity Declaration
9.6.2 CE Conformity Declaration Fig. 46: CE Conformity Declaration Generated: Reviewed: Revised: Status: 300 released Page 37 of 39 Ralph Moretti Document number: Index 28 Sept 2021 235.01551... -
Page 38: Ce Conformity Declaration For Accessories
9.6.3 CE Conformity Declaration for accessories Fig. 47: Conformity Declaration for accessories Generated: Reviewed: Revised: Status: 300 released Page 38 of 39 Ralph Moretti Document number: Index 28 Sept 2021 235.01551... -
Page 39: Supplement 1935/2004
9.6.4 Supplement 1935/2004 Fig. 48: Supplement 1935/2004 Generated: Reviewed: Revised: Status: 300 released Page 39 of 39 Ralph Moretti Document number: Index 28 Sept 2021 235.01551...
Need help?
Do you have a question about the XXL PRO and is the answer not in the manual?
Questions and answers