Related Manuals for Velleman-Kit K8016
Summary of Contents for Velleman-Kit K8016
- Page 1 PC FUNCTION GENERATOR Total solder points: 954 5 ⌧ advanced Difficulty level: beginner 1 K8016 K8016 ILLUSTRATED ASSEMBLY MANUAL H8016IP-1...
- Page 2 Features & specifications Features : frequency range: from 0.01Hz to 1MHz crystal-based stability optically isolated from the PC low sinewave distortion TTL level synchronisation output stores up to 32K of waveform points standard waveforms: sine, square and triangle predefined library waveforms included: noise, sweep, ... includes Windows™...
- Page 3 Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (25-40W) with a small tip.
- Page 4 Assembly hints ⇒ Use the check-boxes to mark your progress. ⇒ Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet. 1.3 Soldering Hints : 1- Mount the component against the PCB sur- face and carefully solder the leads...
- Page 5 Construction 1. Diodes (check the polarity) 3. Resistors (1%) D... R... CATHODE : 10K (1 - 0 - 0 - 2 - 1) : 1N4148 : 1K (1 - 0 - 0 - 1 - 1) : 1N4148 : 1K (1 - 0 - 0 - 1 - 1) : 1N4148 : 1K...
- Page 6 Construction R41 : 200 (2 - 0 - 0 - 0 - 1) : 100nF (104 - µ 1) R42 : 200 (2 - 0 - 0 - 0 - 1) : 100nF (104 - µ 1) R43 : 200 (2 - 0 - 0 - 0 - 1) : 100nF (104 - µ...
- Page 7 Construction 5. IC sockets. 6. Electrolytic capacitors. Check Watch the position of the notch! the polarity ! : 4µ 7 : 1µ F C11 : 4µ 7 C13 : 100µ F C14 : 100µ F C15 : 100µ F C... C16 : 100µ...
- Page 8 Construction 9. Reed relays 12. Voltage regulators (check the position of the notch) VR... RY ... PIN 1 RY... RY1 : VR05R051A 10. Pico fuse IC1 : 7912 (UA7912) FS... IC12 : 7812 (UA7812) IC17 : 7805 (UA7805) FS1 : 1A fast (PFU1) 11.
- Page 9 Construction 14. Connectors 15. IC’s check the position ! (Watch the position of the notch!) J6 : BNC J8 : BNC : 74HC595 : 74HC595 Carefully solder the connections : 74HC4518 : 74HC595 : TDA8702 : 74F161 : 74HC162 SK... + : 74HC14 IC10 : CY7C199 IC11 : 74HC4518...
- Page 10 assembly 16. Voltage regulator and PCB assembly IC23: 7805 (UA7805P) - This regulator must be isolated plastic type ! Attention : The voltage regulator is a fully isolated (plastic) type because it has to be isolated galvanically from the rear panel. Mount the voltage regulator on the rear panel and fasten it with the supplied M3 bolt, washer and nut as shown on the drawing.
- Page 11 Calibration 17. Calibration To allow calibration, the unit must be connected to the computer and the supplied software must be installed. Please consult the ‘Getting Started’ manual for details on the connection and installation procedure. Select the function generator module [Function generator]. Select the correct parallel port [Options >...
- Page 12 24. PCB 18.PCB...
- Page 13 Schematic diagram 19. Power supply section...
- Page 14 Schematic diagram 20. Analogue section...
- Page 15 Schematic diagram 21. Digital section...
- Page 16 VELLEMAN KIT NV Legen Heirweg 33 9890 Gavere Belgium Europe Info ?: http://www.velleman.be Questions ?: support@velleman.be Modifications and typographical errors reserved © Velleman Kit nv H8016IP - 2007 - ED1 (rev1) 5 4 1 0 3 2 9 2 9 0 8 8 7...