Crestron FlipTop FT2 Series Quick Start Manual
Cable management system, 202 size, electrical, pass-through lid
Hide thumbs
Also See for FlipTop FT2 Series:
- Quick start manual (11 pages) ,
- Quick start (2 pages) ,
- Manual (2 pages)
Advertisement
Quick Links
FT2-202-ELEC-PTL
FlipTop™ FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid
The Crestron®
FT2-202-ELEC-PTL
installs into a table or other horizontal surface to provide modular
connectivity. It features a retracting lid that disappears within the
enclosure. When the lid is retracted, six module slots are arranged in one
row. The flexible modular design may also be customized with an
assortment of Crestron accessories, and the pass-through lid style
allows cables to be fully extended while the lid is closed.
For more information about the accessories, please visit
www.crestron.com/Crestron-FlipTops. To configure your FlipTop, launch
the
FlipTop Configuration
Tool.
In the Box
FT2-202-ELEC-PTL
1
Additional Items
2
Locking Bars with screws and gaskets (4532479)
1
Cable, DC Power Splitter (2050094)
1
Connector, Plug (2003575)
1
Holder, Power Supply (2048887)
1
Power Cord, 5 ft 10 in. (1.78 m) (2042043)
1
Power Pack, 24VDC, 2.5 A, 100-240VAC (2045873)
Cutout Template (4529443)
1
FlipTop™ cable management system
Quick Start
1
Advertisement
Related Manuals for Crestron FlipTop FT2 Series
Summary of Contents for Crestron FlipTop FT2 Series
- Page 1 When the lid is retracted, six module slots are arranged in one row. The flexible modular design may also be customized with an assortment of Crestron accessories, and the pass-through lid style allows cables to be fully extended while the lid is closed.
- Page 2 Quick Start FT2-202-ELEC-PTL FlipTop™ FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid Secure the FlipTop Assembly Mount the FlipTop Assembly To prepare the FT2-202-ELEC-PTL and secure it to the table surface: 1. Gently remove the bezel before securing the FT2 assembly to the A mounting hole is required for an FT2-202-ELEC-PTL installation.
-
Page 3: Connect The Network
Cresnet® cable. Custom programming can trigger the retractors after five minutes of no video detected. Connect the FT2 assembly to a Crestron control system or DMPS3 via the 3-pin connector using standard Cresnet cable. The red power lead is not connected and should be terminated. - Page 4 Quick Start FT2-202-ELEC-PTL FlipTop™ FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid Connect and Place the Power Supply 4. Align the four keyed tabs on the power supply holder with four keyed slots on the FT2 assembly. Then, push the power supply holder up and The FT2-202-ELEC-PTL ships with one 24VDC power supply that is used into the slots so that the keyed tabs engage the wide end of the slots.
-
Page 5: Install The Modules
10 mm or thinner, the grommet may be used. www.crestron.com/manuals. 1. Push the connector end of the cable through the hole in the cable The following sections provide best practices and installation procedures plate. - Page 6 Quick Start FT2-202-ELEC-PTL FlipTop™ FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid Installing the Pass-Through Cable Module with Non-4K Cables The grommet is recommended to use with cables that are 10 mm or thinner. 1. Open the grommet. 2. Insert a cable into the grommet with the connector facing up toward the user.
- Page 7 Quick Start FT2-202-ELEC-PTL FlipTop™ FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid Install the Blank and Keystone Plate Module 6. Attach the side plate to the module by snapping the plastic clips on the plate into the two slots on the module. Blank plate modules (sold separately) fill empty slots in module rows, and keystone plate modules (sold separately) allow for cables NOTE:...
-
Page 8: Install The Bezel
Quick Start FT2-202-ELEC-PTL FlipTop™ FT2 Series Cable Management System, 202 Size, Electrical, Pass-Through Lid Install the Locking Bars Install the Bezel To install the locking bars: Place the bezel onto the FT2 assembly so that the retractable lid fits inside the bezel opening. The bezel is held in place using magnets. 1. - Page 9 3. Close the lid by lifting it vertically and returning it over the FT2 licensed to Crestron dealers, CSPs, and end-users under a separate End-User License assembly. Agreement. Both of these Agreements can be found on the Crestron website at www.crestron.com/legal/software_license_agreement. The product warranty can be found at www.crestron.com/warranty.