Advertisement

SERVO-DRIVE for AVENTOS
Installation instructions – Original
AVENTOS HF
AVENTOS HS
AVENTOS HL
AVENTOS HK

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AVENTOS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for BLUM AVENTOS

  • Page 1 SERVO-DRIVE for AVENTOS Installation instructions – Original AVENTOS HF AVENTOS HS AVENTOS HL AVENTOS HK...
  • Page 2: Table Of Contents

    Structural changes and spare parts Disposal Function Planning information Orientation diagram Assembly Blum distance bumper Distribution cable Drive unit Orientation diagram Blum transformer and accessories Assembly Blum transformer and accessories SERVO-DRIVE switch Functions SERVO-DRIVE for AVENTOS Start-up SERVO-DRIVE for AVENTOS Deactivation SERVO-DRIVE for AVENTOS...
  • Page 3: Using The Installation Instructions

    However, only AVENTOS HF is used as an example in the illustrations. ⇒ Please see the special AVENTOS installation instructions for the assembly steps of the mechanical AVENTOS HF, HS, HL and HK lift systems without SERVO-DRIVE. Safety Principle SERVO-DRIVE for AVENTOS complies with current safety standards.
  • Page 4: Safety Information

    Blum transformer or modify any cabling. ⇒ The device may only be connected to a power supply that corresponds to the type and frequency listed on the serial tag (see Blum transformer). ⇒ The outlet must be freely accessible.
  • Page 5: Structural Changes And Spare Parts

    Structural changes Structural changes and spare parts not approved by the manufacturer affect and spare parts the safety and functionality of SERVO-DRIVE for AVENTOS and are, therefore, not allowed. ⇒ Only use original spare parts from Julius Blum GmbH. ⇒...
  • Page 6 From cabinet front edge for fronts that protrude below Recommendation for aluminium frames: Consider drilling Blum distance bumper into the cabinet side. A trial application must be carried out when fixing the Blum distance bumper to the front. Do not glue the Blum distance bumper...
  • Page 7: Planning Information

    Connecting piece [2] half KB (KS 16–19mm) -193 mm Cabinet width Side panel thickness Blum transformer safety distance A safety distance of 30 mm must be maintained for air circulation; otherwise, there is a risk that the CAUTION Blum transformer could overheat.
  • Page 8: Orientation Diagram

    SERVO-DRIVE switch with battery display Blum distance bumper Blum transformer with LED display Front Transformer unit housing Cabinet Assembly Blum distance bumper Aluminium frame: Installation in the cabinet side Installation in the front Do not glue the Blum distance bumper...
  • Page 9 Assembly Distribution cable AVENTOS HF / -HS / -HL ✓ ✓ AVENTOS HK ✓ ✓ Adjustment Drive unit AVENTOS HF / -HS / -HL LOCKED AVENTOS HK...
  • Page 10: Assembly

    The drive unit can be locked when the orange slide is no longer visible in the view window. NOTICE AVENTOS HF / -HS / -HL AVENTOS HK The drive unit can be locked once it is correctly located on the AVENTOS mechanism. NOTICE AVENTOS HK...
  • Page 11 Orientation diagram Blum transformer and accessories Assembly on the top panel Assembly in combination with SERVO-DRIVE for pull-out systems CAUTION Only 1 Blum transformer can be connected to each distribution cable. Back cabling Upper cabling...
  • Page 12 Assembly Blum transformer and accessories Pull-out stop Do not damage piercing pins. Assembly SERVO-DRIVE switch...
  • Page 13: Start-Up

    Overview SERVO-DRIVE for AVENTOS functions Start-up Activating the SERVO-DRIVE switch Additional features Activating synchronisation Activating collision avoid- ance Start reference run Deactivation Reset Motion Reset Wireless Button layout Drive unit <Reset Motion> button Motion LED <SWITCH> button <SYNC> button <COLL> button <Reset Wireless>...
  • Page 14 Start-up SERVO-DRIVE for AVENTOS Operation Lights up continuously Flashes Activating the Setting up the wireless connection between the SERVO-DRIVE switch and the drive unit. SERVO-DRIVE switch Each switch can only be allocated to one SERVO-DRIVE unit. Press the <SWITCH> button until the LED flashes green.
  • Page 15 Start-up SERVO-DRIVE for AVENTOS additional features Operation Lights up continuously Flashes Up to three drive units can be synchronised allowing them to move simultaneously. Activating synchronisation This function is required for several cabinets with a uniform front. Activating the SERVO-DRIVE switch → see A 1–3.
  • Page 16 Deactivation SERVO-DRIVE for AVENTOS Flashes quickly Reset Motion Resets the reference run and enables a new reference run to be started. Press the <Reset Motion> button using a pen (at least 3 seconds) until the LED flashes quickly. Reset Wireless Deactivates all functions.
  • Page 17: Assembly Cover Cap

    Assembly Cover cap Replacement SERVO-DRIVE switch battery When battery power begins to weaken, the SERVO-DRIVE switch battery display flashes red. NOTICE ⇒ Only use type CR2032 batteries from known manufacturers. ⇒ Make sure that the new battery is inserted correctly (note proper pole connections +/-).
  • Page 18: Removal Drive Unit

    Drive unit ⇒ Before starting repair or maintenance work, unplug the Blum transformer to disconnect the power. ⇒ Never open a Blum transformer. There is a danger of electric shock. DANGER AVENTOS HF / -HS / -HL AVENTOS HK Removal...
  • Page 19: Troubleshooting

    (leaning pro- DRIVE switch for a briefer time tection triggered) Blum transformer is not connected • Connect the flex to the Blum trans- to the power outlet former and to the power outlet • Turn on the switched outlet...
  • Page 20 Switched outlet is turned off Turn on switched outlet transformer does not light Blum transformer is not connected Connect the flex to the Blum trans- to the power outlet former and to the power outlet Blum transformer is defective Replace Blum transformer LED does not light on •...
  • Page 21 Problem Possible cause Remedy Front does not open No Blum distance bumper is Install Blum distance bumper when pressing on the installed → see planning information front, but it does close ╵ → There is no 2 mm bumper path...
  • Page 22 Problem Possible cause Remedy Reference run for The SERVO-DRIVE switch is not Activate the SERVO-DRIVE switch drive unit cannot be activated undertaken. ╵ → Motion LED on the Drive unit is not attached properly to Correctly install drive unit drive unit flashes the lift mechanism orange Front is not balanced...
  • Page 23 ╵ → <Wireless> LED lights red ⇒ If the SERVO-DRIVE for AVENTOS electrical motion support system does not work, lift systems can still be opened and closed manually – they will not be damaged in this way. NOTICE...
  • Page 24 EC Declaration of Conformity Julius Blum GmbH, Industriestr. 1, A-6973 Höchst herewith declare on our own responsibility that the product SERVO-DRIVE for AVENTOS (Z10NE050.xx, Z10NE010.xx, 21xA0x1.xx, 21P5020.xx, 21P0020.xx, 21.A00L33.xx, Z10ZE000.xx) to which this Declaration refers, complies with the following EU Directives:...

This manual is also suitable for:

Aventos hfAventos hsAventos hlAventos hk

Table of Contents