Code Alarm PROFESSIONAL Series Installation Manual
Security and keyless entry
Hide thumbs
Also See for PROFESSIONAL Series:
- Installation manual (49 pages) ,
- Owner's manual (12 pages) ,
- Installation quick reference manual (2 pages)
Related Manuals for Code Alarm PROFESSIONAL Series
Summary of Contents for Code Alarm PROFESSIONAL Series
- Page 1 PROFESSIONAL SERIES Security and Keyless Entry Installation Guide ca1155 **This guide is a reference for module firmware version 5.0 or higher** 2020 Voxx Electronics Corporation. All rights reserved.
-
Page 2: Table Of Contents
Table of Contents Before You Begin ..................3 Wire Connection Guide ................4 12 Pin Main Harness ................. 5 10 Pin Input / Output Harness ..............8 Door Locks ....................11 Additional Ports ..................12 LED Port ....................12 Programming Port ................... 12 Shock Sensor Port .................. -
Page 3: Before You Begin
BEFORE YOU BEGIN PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces... -
Page 4: Wire Connection Guide
12 Pin Main Harness BROWN SIREN OUTPUT ( + ) BATTERY 12V ( + ) BLACK GROUND BROWN/BLACK UNLOCK SWITCH ( 87A ) VIOLET/BLACK UNLOCK POLARITY ( 87 ) WHITE/BLACK LOCK SWITCH ( 87A ) GREEN/BLACK LOCK MOTOR ( 30 ) WHITE PARKING LIGHT OUTPUT WHITE/RED... -
Page 5: 12 Pin Main Harness
12 Pin Main Harness BROWN SIREN OUTPUT ( + ) Locate a suitable mounting location in the engine compartment for the siren, away from moving parts. With the bell of the siren aiming downwards, secure the siren in place using self tapping screws, being careful not do drill into any hoses, wiring or components. - Page 6 BROWN/BLACK UNLOCK SWITCH ( 87A ) Refer to the Door Lock Section on page 11 of this guide. VIOLET/BLACK UNLOCK POLARITY ( 87 ) Refer to the Door Lock Section on page 11 of this guide. WHITE/BLACK LOCK SWITCH ( 87A ) Refer to the Door Lock Section on page 11 of this guide.
- Page 7 VIOLET LOCK POLARITY ( 87 ) Refer to the Door Lock Section on page 11 of this guide. BLUE/BLACK UNLOCK MOTOR ( 30 ) Refer to the Door Lock Section on page 11 of this guide. 2020 Voxx Electronics Corporation. All rights reserved.
-
Page 8: 10 Pin Input / Output Harness
10 Pin Input / Output Harness PURPLE DOOR TRIGGER INPUT ( + ) Locate the vehicle’s dome light or door pin switch wire. Verification: This wire will register positive voltage (POS) when the door is opened and the interior light is on. This wire will register ground or “0”... - Page 9 ORANGE GROUND WHEN ARMED OUTPUT ( - ) This wire will have a continuous ( - ) 300mA output when the system is Armed. This wire is typically used for controlling window modules or additional sensors. BROWN/BLACK HORN OUTPUT ( - ) Locate the vehicle’s horn wire.
- Page 10 RED/WHITE TRUNK RELEASE OUTPUT ( - ) Locate the vehicle’s trunk release wire at the trunk release switch. Verification: This wire will register either positive voltage or ground when the trunk release is activated. This is a low current output, 300mA. ca1155 rev B...
-
Page 11: Door Locks
Door Locks BROWN/BLACK UNLOCK SWITCH ( 87A ) BLUE/BLACK UNLOCK MOTOR ( 30 ) VIOLET/BLACK UNLOCK POLARITY ( 87 ) WHITE/BLACK LOCK SWITCH ( 87A ) GREEN/BLACK LOCK MOTOR ( 30 ) VIOLET LOCK POLARITY ( 87 ) The door lock / unlock outputs are designed to control several different types of systems which may require additional parts. -
Page 12: Additional Ports
Additional Ports LED Port The LED included in the kit will serve as a visual indicator of the alarm’s status. It should be installed in the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver. Once a location has been selected, check behind the panel for wire routing access, and to confirm the drill will not damage any existing components as it passes through the panel. -
Page 13: Set Up & Programming
Set Up & Programming Transmitter Programming - Feature Bank 1 Turn the ignition ON. Press and hold the valet/override button. Within 10 seconds the system will chirp (3) three times. Press 1 button of each transmitter you wish to program. The system will respond with 1 chirp for each accepted transmitter. -
Page 14: Programming Feature Banks
Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming. Feature Bank 2 - 4 Chirps 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash Security Control Silent Choice Door Locks Active Passive... -
Page 15: Pc Based Feature Programming / Firmware Updates (Optional)
To Use a PC and VEPROG tool for Feature Programming or Firmware Updates: Download and install the Code Alarm Utility App. from the Voxx Tech / Software Downloads section of voxxuniversity.com (login required) Launch the Code Alarm Utility App. -
Page 16: Adjusting The Shock Sensor
Adjusting the Shock Sensor Increase sensitivity by turning the adjustment dial clockwise. Decrease sensitivity by turning the adjustment dial counter clockwise. Testing the Shock Sensor Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike the vehicles bumper. -
Page 17: Chirp Delete - User Accessible
Chirp Delete - User Accessible System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks. Turn the ignition ON then OFF. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF. User Selectable LED This feature will control whether the LED is ON or OFF when the system is Armed/ Locked. - Page 18 4 - System Notifications: This feature selects which output(s) will sound the system’s arm/disarm chirps. This feature does not effect the triggered state of the security system and during a triggered cycle, both the siren and horn outputs will activate respectively. Siren &...
- Page 19 10 - Arm/Disarm Chirps: Determines the number of chirps and parking light flashes when the system is armed/disarmed. Standard - 2 chirps/light flashes with arm, 1 chirp/light flash with disarm. Inverted - 1 chirp/light flash with arm, 2 chirps/light flashes with disarm. 11 - LED Indicator: Control of the LED when the system is armed / locked.
- Page 20 16 - Dome Light Delay, Preset Time or Programmable: The system can be programmed to delay arming after the lock button is pressed based on preset delay times or a customizable delay time. OFF/Program Custom Time - There will be NO delay unless a custom delay time has been learned.
- Page 21 3 - Ignition Locks: Control of door locks when the ignition is cycled ON or OFF. OFF - Door locks not activated by ignition. Lock / Unlock - Doors lock when ignition is turned on and unlock when ignition is turned off. Lock Only - Doors lock when ignition is turned on.
-
Page 22: Transmitter Button Functions
Transmitter Button Functions Car Find / 4-Button Lock Unlock Trunk Panic Transmitter Operation Method Lock Press and Release Unlock Press and Release Trunk Push and Hold (3 Sec) Car Finder Press and Release Push and Hold (3 Sec) Panic AUX 1 Push and Hold (3 Sec) Press and Release Lock then Press Shock Bypass... -
Page 23: System Layout
BROWN SIREN OUTPUT ( + ) BATTERY 12V ( + ) BLACK GROUND BROWN/BLACK UNLOCK SWITCH ( 87A ) VIOLET/BLACK UNLOCK POLARITY ( 87 ) VIOLET LOCK POLARITY ( 87 ) GREEN/BLACK LOCK MOTOR ( 30 ) WHITE PARKING LIGHT OUTPUT WHITE/RED PARKING LIGHT INPUT WHITE... - Page 24 VOXX Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
Need help?
Do you have a question about the PROFESSIONAL Series and is the answer not in the manual?
Questions and answers