Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-TD10M-1
Summary of Contents for HIKVISION DS-TD10M-1
- Page 1 DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual...
- Page 2 © 2019 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved. ALL RIGHTS RESERVED. This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
- Page 3 DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
-
Page 4: Table Of Contents
DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual TABLE OF CONTENTS Chapter 1 Radar Installation ................4 1.1 Installation Parameters ................4 1.2 Install Radar ....................4 1.3 Wire Radar ....................5 Chapter 2 Operation via Radar Debugging Software ......... 7 2.1 Overview ......................7 2.2 Running Environment ...................7... -
Page 5: Chapter 1 Radar Installation
DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Chapter 1 Radar Installation DS-TD10M-1 radar is usually installed in the middle position of gantry and L-shaped pole, as shown in Figure 1-1. Figure 1-1 Radar Installation 1.1 Installation Parameters Installation height: 6 m ... -
Page 6: Wire Radar
DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Figure 1-2 Radar Installation Angle 1.3 Wire Radar The radar is powered by 12 VDC, and it will be burnt if powered by 220 VAC. The radar and capture camera communicate via RS-485 serial port with 3 signal lines, among which the blue one indicates D+, yellow indicates D-, and green indicates DGND. - Page 7 DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Figure 1-3 RS-485 DB9 Header Connection...
-
Page 8: Chapter 2 Operation Via Radar Debugging Software
Chapter 2 Operation via Radar Debugging Software 2.1 Overview This software is the debugging software for DS-TD10M-1 radar. It is used to configure parameters of the radar for installation, debugging, and troubleshooting. The software installation package is included in the product CD. -
Page 9: Operate Via Software
DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual 3. Click Next and then select an installation path, as shown in Figure 2-2. Figure 2-2 Select Installation Path 4. Click Next to continue. The setup wizard will complete the software installation automatically, as shown in Figure 2-3. - Page 10 DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual There are three working modes of the software: debug mode, test velocity mode, and measure mode. Switch the radar to different working modes via the software. The software enters the interface as shown in Figure 2-4 after running.
- Page 11 DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Parameters Reading: Read the current road information and installation parameters. WiFi Password Setting: Edit the current WiFi password connected to the radar. Restore Factory Setting: Restore the parameters and road information to default status.
-
Page 12: Connect Radar
DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Figure 2-5 Advanced Settings Interface Radar Status Area displays the current status of radar, including software version, product serial number and current setting parameters. 2.4.1 Connect Radar Steps: 1. Select Device Connect, and the connection setting dialog box will pop up. As shown in Figure 2-6, there are two connection methods: WIFI connection and Serial connection. -
Page 13: Debug Radar
DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Figure 2-6 Device Connection Settings 4. (Optional) You can also select the connection method as WIFI connection. The computer must have been connected to the radar via WiFi in advance. Click OK and the device will connect automatically. - Page 14 DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Firstly, the moving track should be straight and the initial appearance distance should be greater than the trigger distance. Otherwise, some of the targets will be undetectable. For instance, if the trigger distance of Towards Direction is set as 28 meters, the appearance distance should be set as about 35 meters.
-
Page 15: Chapter 3 Faq
DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual Chapter 3 FAQ Connecting to software failed. – Check whether the computer has been installed a serial port driver, and then view the port number in device management module. – If the radar is connected to the software, the serial port parameters are set as follows: baud rate 115200, data bit 8, stop bit 1, parity none. - Page 16 DS-TD10M-1 Multi-Target Speed-Measuring Radar User Debugging Manual...
Need help?
Do you have a question about the DS-TD10M-1 and is the answer not in the manual?
Questions and answers