IDW G Series Instruction Manual

IDW G Series Instruction Manual

Upright cooler
Hide thumbs Also See for G Series:

Advertisement

Quick Links

G-7f/GCG-7f
UPRIGHT COOLER
Manual is for the following models:
G-7F
G-7FB
GCG-7F
GCG-7FB
GCG-7F2
GCG-7-FB31N*
GCG-7-F31N*
G-7-FB31N *
G-7-F31N*
GCG-7-F231N*
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for IDW G Series

  • Page 1 G-7f/GCG-7f UPRIGHT COOLER Manual is for the following models: G-7F G-7FB GCG-7F GCG-7FB GCG-7F2 GCG-7-FB31N* GCG-7-F31N* G-7-FB31N * G-7-F31N* GCG-7-F231N* Instruction Manual...
  • Page 2: Table Of Contents

    G-7f/GCG-7f FOR YOUR FUTURE REFERENCE • This easy-to-use manual will guide you in getting the best use of your cooler. • Remember to record the model number and the serial number. This information can be found on the inside of your cooler. •...
  • Page 3: Parts & Identification

    By law, disposal of hazardous wastes may be subject to fi nes and imprisonment under the provisions of the of hazardous wastes may be subject to fines and imprisonment under the privisions of the environmental regulations. 14. Large shelf (2) 28. Switch panel 42. Lower left hinge cover environmental regulations. Innovative DisplayWorks Innovative DisplayWorks offi ce 909.447.8254 • fax 909.305.8756 • toll free 877.307.2665 • www.idw.global...
  • Page 4: Features

    The refrigeration unit is designed for easy access, allowing for fast and simple repairs. • • This equipment is intended for storage and display of non-hazardous packaged product. IDW requires that a sole use circuit be dedicated for the unit. Failure to do so voids warranty. • This equipment is intended for storage and display of non-hazardous packaged product. WARNING: Do not use extension cords.
  • Page 5: Replacing The Interior Light

    G-7f/GCG-7f Instruction Manual REPLACING THE DOOR LED LIGHTS REPLACING THE INTERIOR LIGHT Unplug the cooler. Disconnect top Remove light strand. plastic cover. Using a small flathead, pry up the plastic cover. Disconnect middle light Unscrew light strand. strand. Disconnect the lights. Remove entire light strand. To install LED lights follow the above instructions in reverse order. Notes: If there are any malfunctions with the main control panel of LED lights, please contact a professional for replacement. Unscrew (3) screws using a Phillip’s screwdriver. SETTING UP SPACER & POWER CORD HOLDERS The G-7f/GCG-7f is supplied with one set (2 pieces) of Spacers to hold the extra length of Power Cord Take out the two Spacers and screws supplied in the Accessory Pack shipped with Remove LED light strand. the Cooler.
  • Page 6: Startup, Operation & Temperature Adjustment

    G-7f/GCG-7f Instruction Manual STARTUP, OPERATION AND TEMPERATURE ADJUSTMENT Operation • Prior to stocking cooler with product, it should be operated empty for half an hour. Using a screwdriver, remove the (3) screws from Temperature Adjustment the refrigeration drawer base plate. • G7f/GCG-7f performance testing position of the thermostat is around 4.5-6. Lit Door “Logo” Switch - For GCG-7f Models Only Operation Slide the Refrigeration Drawer out to easily access • The light switch located at the bottom left hand side on the rear of the refrigeration components. Remove the component to replace cabinet is the ON/OFF switch for the Lit logo located on the door of the or repair. cooler. REPAIR AND MAINTENANCE FOR REFRIGERATION DRAWER Using plastic bristle brush, carefully clean the coil being aware * A CERTIFIED TECHNICIAN IS REQUIRED TO REPAIR ALL REFRIGERATION COMPONENTS FOR that fins can be bent or be damaged if too much force is used WARRANTY PURPOSES.
  • Page 7: Reversible Door Exchange

    G-7f/GCG-7f Instruction Manual DOOR REVERSAL (For G-7f Coolers Only) DOOR REVERSAL Cont. (For G-7f Coolers Only) 1 Remove the plastic cover on the bottom hinge, disconnect the reversible   d oor   e xchange   terminals and then hide the terminals in the door’s reserved hole. 8 Feed the wiring terminals through the hinge and connect the terminals. 1.disassemble   t he   t he   h inge   l atch   o f   l eft   h and   d oor. 2.  ...
  • Page 8: Troubleshooting

    G-7f/GCG-7f Instruction Manual TROUBLESHOOTING G-7f CIRCUIT DIAGRAM The following are not Malfunctions: Issues Solutions Liquid fl owing noise within cooler This liquid is the sound of the cooling agent fl owing through the pipes. Refrigeration system is shutdown for This refrigerator has a strong level of heat preservation and can main- longer periods of time while temperature tain a relatively ambient temperature.
  • Page 9 G-7f/GCG-7f Instruction Manual G-7f 220V ELECTRICAL WIRING DIAGRAM GCG-7f 220V ELECTRICAL WIRING DIAGRAM GCG-7F ELECTRICAL WIRING DIAGRAM 220Volts/50HZ./1PHASE G-7F ELECTRICAL WIRING DIAGRAM 220Volts/50HZ./1PHASE Innovative DisplayWorks...
  • Page 10 Innovative DisplayWorks, Inc. To locate the distributor in your area go to: http://www.idw.global/contact/#distributors...

Table of Contents