Advertisement
2.4
Position the internal rail (GM86085) at the location
shown in Figure 5 using the mounting bracket and
hardware identified in Figure 7.
Position a mounting bracket (GM86091) to the top
of the internal rail using four bolts (X-6224-20) and
four nuts (X-6210-7). See Figure 15 for more
detail.
Note: Do not final tighten at this time.
1
1. Bolt (X-6238-3 or X-6238-11 qty. 4) and washer (X-25-37
qty. 4)
2. Bolt (X-6224-20 qty. 8), nut (X-6210-7 qty. 8), and washer
(X-25-37 qty. 8)
3. Corner extrusion mounting bracket (GM85875 qty. 4)
Figure 6 Corner Extrusion Mounting Bracket
Installation (Corner Rails to Base, 4 Places)
1
1. Extrusion mounting bracket (GM85876 qty. 3)
2. Bolt (X-6224-20 qty. 6), nut (X-6210-7 qty. 6), and washer
(X-25-37 qty. 6)
3. Bolt (X-6238-3 or X-6238-11 qty. 6) and washer (X-25-37
qty. 6)
Figure 7 Extrusion Mounting Bracket Installation
(Rails to Base, 3 Places)
2.5
Position the LH and RH bulkheads (GM86075 and
GM86076) as shown in Figure 5 (items 7 and 8).
4
2.6
2
3
GM86396A-
2.7
2
2.8
3
GM86396A-
Note: Do not final tighten at this time.
Secure the bottom of the bulkheads to the existing
skid using a screw (M933-06020-60), washer
(X-25-40) and nut (M6923-06-80) for each
bulkhead.
Secure the sides of the bulkheads to the two
internal rails using a bolt (X-6224-20), washer
(X-25-37), and nut (X-6210-7) for each bulkhead.
Position the upper bulkhead (GM86074) as
shown in Figure 5 (item 4).
Secure the bottom of the upper bulkhead to the LH
and
RH
bulkheads
(M933-06020-60), two washers (X-25-40) and
two nuts (M6923-06-80) for each bulkhead.
Secure the sides of the upper bulkhead to the
internal rails using a bolt (X-6224-20), washer
(X-25-37), and nut (X-6210-7) for each side rail
Position the internal rail (GM86084) as shown in
Figure 5 (item 2).
Secure the internal rail to the upper bulkhead
panel using two bolts (X-6224-20), two washers
(X-25-37), and two nuts (X-6210-7).
On each end of the internal rail, secure a mounting
bracket (GM86091) using four bolts (X-6224-20)
and four nuts (X-6210-7) per bracket.
Figure 15 for more detail.
Position the internal rail (GM86082 or GM86083)
as shown in Figure 5 (item 12).
Secure the internal rail to the corner rail using a
mounting
bracket
(GM86091),
(X-6224-20) and four nuts (X-6210-7).
Figure 15 for more detail.
Secure the other end of the internal rail to the rail
using a mounting bracket (GM86091), four bolts
(X-6224-20) and four nuts (X-6210-7).
Figure 15 for more detail.
using
two
screws
See
four
bolts
See
See
TT-1601
5/16
Advertisement
