Advertisement
Quick Links
www.ggm.co.kr
GLOBAL GEARED MOTOR
OPERATION MANUAL
GUD
SERIES
DIGITAL
SPEED CONTROL UNIT
■ Headquarters / 1st Factory : 22, Gyeongin-ro 3beon-gil, Bucheon-si, Gyeonggi-do, Republic of Korea
Tel:(032)664-7790 Fax:(032)611-7791
■ Attached research institute / No. 2 factory : 180, Oksan-ro, Bucheon-si, Gyeonggi-do, Republic of Korea
Tel:(032)684-7791 Fax:(032)683-5059
GGM Co., Ltd.
Advertisement
Related Manuals for GGM GUD Series
Summary of Contents for GGM GUD Series
- Page 1 SPEED CONTROL UNIT ■ Headquarters / 1st Factory : 22, Gyeongin-ro 3beon-gil, Bucheon-si, Gyeonggi-do, Republic of Korea Tel:(032)664-7790 Fax:(032)611-7791 ■ Attached research institute / No. 2 factory : 180, Oksan-ro, Bucheon-si, Gyeonggi-do, Republic of Korea Tel:(032)684-7791 Fax:(032)683-5059 GGM Co., Ltd.
- Page 2 Thank you for purchasing this GGM product. Please do not use this product until you have read this user's guide thoroughly and familiarized yourself with the knowledge, safety information and precautions related to the product that it contains. After reading this user's guide, keep it at hand to use as a reference whenever it is needed.
- Page 3 Ignoring the following warnings and Caution instructions on the handling of the product may result in injury or property damage. • Do not use the motor or the speed controller beyond its specifications. Doing so may cause injury or damage to the product. •...
- Page 4 2. Confirmation when the product is handed over - Confirm that the delivered product is the product you ordered. - If a different product is installed, there is a risk of injury or fire. - Contact a nearby retail store if there is a shortage compared to the number of the products you ordered or if a damaged product is delivered.
- Page 5 4. CONTROLLER CODING SYSTEM 6 : 6W Single Phase 15 : 15W 220V 50/60Hz 230V 50/60Hz 25 : 25W 240V 50/60Hz Unit Digital 40 : 40W Co.,LTD. Type Type 60 : 60W Single Phase 90 : 90W 110V 50/60Hz 115V 50/60Hz 120:120W 180:180W 5.
- Page 6 6. Characteristics of the product ① Indicates the current rotation speed (r/min). ② The motor speed can be controlled simply by connecting the motor and the control unit using the dedicated connector, and connecting the AC terminal to the power source. ③...
- Page 7 8. Names and functions of each part - 7 -...
- Page 8 9. Wiring method 9-1 Power and motor wiring ▶ Connect the motor connector to the motor connector terminal at the back of the controller. ▶ Connect the AC power to power supply terminals No. ① and No. ②. SW1 contact capacity AC 125V or 250V 5A or higher ▶...
- Page 9 9-3 Multi-level speed wiring method ▶You can set the speed in 4 levels by connecting to I/O input terminals No. ③, No. ④ and No. ⑤. SW4 SW5 MOTOR rotation speed OFF OFF Set speed at the front ON OFF SPD 1 set speed OFF ON SPD 2 set speed...
- Page 10 10. Operation and parameter setting sequence 10-1 Operation sequence ① Supplying the AC power (Connect the AC power to the power supply terminals No. ① and No. ②) The indicator lamp illuminates. (Rotation speed) ② Controlling the operation key (operation) When you press the RUN/STOP key, the motor will start rotating at the set speed.
- Page 11 10-2 Parameters Display Function Range Default Note unit value Reduction gear ratio setting RATE Reduction REAL RPM = gear Motor rotation speed / Reduction gear ratio ratio S-ON Accele Mode set to accelerate the 0~15 ration rotation of the motor slowly time (increments of 0.1 second) SOFF...
- Page 12 10-3 Parameter setting sequence ① Supplying AC power The indicator lamp illuminates. (Rotation speed) ② Entering Parameter mode (Press and hold) Press and hold the CW/CCW key (for 3 seconds or longer) to enter Parameter mode. ③ Selecting a parameter (9 parameters) Press the Arrow keys to select the desired parameter.
- Page 13 10-4 Setting method if using the reduction gear ratio (ex. 1/10 of the reduction gear ratio) ① Supplying AC power The indicator lamp illuminates. (Rotation speed) ② Entering Parameter mode (Press and hold) Press and hold the CW/CCW key (for 3 seconds or longer) to enter Parameter mode.
- Page 14 10-5 Setting method if using the electromagnetic brake ① Supplying AC power The indicator lamp illuminates. (Rotation speed) ② Entering Parameter mode (Press and hold)) Press and hold the CW/CCW key (for 3 seconds or longer) to enter Parameter mode. ③...
- Page 15 11. Installation method (Panel process drawing) - Drill a hole in the installation panel as shown in the figure below. Assemble the controller body and the front cover, and fix them using M4 screws and nuts. (Use an installation panel with a thickness of 2mm or less) 12.
- Page 16 ※ Contact the retail store where you purchased the product or our Factory 2 if you have any product inquiries or customer service requests. Leader of geared motor GGM CO.,LTD. http://www.ggm.co.kr Headquarters / 1st Factory Attached research institute / No. 2Factory...
Need help?
Do you have a question about the GUD Series and is the answer not in the manual?
Questions and answers