Related Manuals for Zte CDMA2000
Summary of Contents for Zte CDMA2000
- Page 1 CDMA2000 1X EV-DO Wireless Data Terminal User Guide CDMA2000 1X EV-DO Wireless Data Terminal User Guide This User Guide is used for Wireless Data Terminal of AC2787_V3. ZTE Corporation http://www.zte.com.cn...
- Page 2 No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice. ZTE Corporation...
-
Page 3: Table Of Contents
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Table of Contents 1. Introduction ..........................1 2. Precautions ..........................1 3. Appearance ..........................2 3.1 Introduction ......................... 2 3.2 Insert R-UIM Card ......................2 3.3 Operation Guide of Data Cable ................... 3 4. -
Page 4: Introduction
Thank you for choosing ZTE Corporation’s CDMA2000 Wireless Data Terminal (hereinafter referred to as Data Terminal). Data Terminal supports both CDMA2000 1X EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing on the Internet, send & receive short messages, and make &... -
Page 5: Appearance
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 3. Appearance 3.1 Introduction Side View Rear View 3.2 Insert R-UIM Card Note: If your data terminal doesn’t need R-UIM card, please skip this section. 1. Pull out the tap； 2. Take out the R-UIM card cover in the direction indicated by the arrow；... -
Page 6: Operation Guide Of Data Cable
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 4. Push back R-UIM card cover. 3.3 Operation Guide of Data Cable Generally, the Data Terminal could be directly connected with USB port. You could also connect the Data Terminal with PC by using the accompanying data cable, as shown in the following figure. -
Page 7: Install
CDMA2000 1X EV-DO Wireless Data Terminal User Guide under Windows XP. Do not insert the Data Terminal before installation. 4.2.1 Install 1. Please connect Data Terminal to PC through USB interface. You could use the data cable to connect. 2. The installation driver will automatically run. Please install according to the installation wizard. -
Page 8: Connect/Disconnect
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 1X indication Call indication EV-DO indication Missed call indication (Support Rev.0 and Rev.A) Signal strength indication. The more Unread message bars there are, the stronger signals are. indication CDMA network unavailable Inbox full indication... -
Page 9: Connection Records
CDMA2000 1X EV-DO Wireless Data Terminal User Guide After connecting to Internet, click 7. Connection Records Click icon to view connection records. Connection records save the previous relevant information including Start at, Duration and Transmit bytes, which will help you know the status easily. - Page 10 CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button in the right side of the interface or press “Enter” to make a call. Receive a call When there is an incoming call, your computer will alert and the incoming caller ID will appear on the interface.
-
Page 11: Call History
CDMA2000 1X EV-DO Wireless Data Terminal User Guide 9. Call History (If this feature is not supported by your Data Terminal, please skip over this chapter.) Click icon to view the call history. The outgoing/incoming calls are saved in call history, including missed calls, incoming calls, outgoing calls, and talk duration. -
Page 12: Phone Book
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click button to save the text into Draftbox. The received messages will be saved in the Data Terminal In-box. You could copy the messages from the Data Terminal In-box to PC In-box by selecting Copy or Copy All;... -
Page 13: Setting
CDMA2000 1X EV-DO Wireless Data Terminal User Guide Click then input the contents and select “OK” to add a new contact. Edit Click then edit the contents and select “OK” to edit the contact information. Search for contacts ... - Page 14 CDMA2000 1X EV-DO Wireless Data Terminal User Guide Set the network parameters (phone number, username, password), work mode, etc. After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current interface to factory default.
-
Page 15: Help
CDMA2000 1X EV-DO Wireless Data Terminal User Guide After the setting, click “call” button to send the corresponding request to the network system. After the setting, click “Apply” button to save the settings on the current interface. ... - Page 16 CDMA2000 1X EV-DO Wireless Data Terminal User Guide damaged. Wrong setting of parameters. (Phone, Correct the parameter settings. Consult your User, Password.) service provider for details. Dialing failed Not enough money. Consult your service provider for details. Network congestion or failure.
-
Page 17: Fcc Regulations
CDMA2000 1X EV-DO Wireless Data Terminal User Guide be restarted to run normally. 15. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 18 CDMA2000 1X EV-DO Wireless Data Terminal User Guide The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid...
Need help?
Do you have a question about the CDMA2000 and is the answer not in the manual?
Questions and answers