Page 1
KW58283 Wireless ADSL Router User Manual...
Page 2
Wireless ADSL Router USER MANUAL NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.
Wireless ADSL Router USER MANUAL 1 Overview Thank you for choosing our product. The KW58283 Wireless ADSL Router uses Broadcom’s CPE solution that fully complies with ADSL, ADSL2,ADSL2+ and IEEE802.11b/g/n standards. It will provide your SOHO with convenient Internet access.
Page 5
Wireless ADSL Router USER MANUAL Internet Control Message Protocol (ICMP) IP Static Routing Routing Information Protocol (RIP, RIPv2) Network Address Translation (NAT) Virtual Server, Port Forwarding Dynamic Host Configuration Protocol (DHCP) DDNS Simple Network Time Protocol (SNTP) ...
Wireless ADSL Router USER MANUAL Stateful Packet Inspection (SPI) Denial of Service Prevention (DoS) 1.1.7 Management Support Web Based GUI Upgrade or update via FTP/HTTP Command Line Interface via Telnet Diagnostic Test Firmware upgrade-able for future feature enhancement 1.1.8 Operating System Support...
Wireless ADSL Router USER MANUAL Subscription for ADSL service. Your ADSL service provider should provide you with at least one valid IP address (static assignment or dynamic assignment via dial-up connection). One or more computers, each contains an Ethernet 10/100M Base-T network interface card (NIC).
Wireless ADSL Router USER MANUAL 2 Hardware Description Front Panel Color Function On: Power on Green Off: No power On: LAN link established and active via LAN port Green Blinking: ADSL data activity occurs Off: No LAN link via LAN port On: The wireless module is ready and idle Green Blinking: Data transmitting or receiving over WLAN...
Page 9
Wireless ADSL Router USER MANUAL Rear panel Port Function Connect the device to an ADSL telephone jack or splitter using a RJ-11 telephone cable Connect the device to user’s PC's Ethernet port, or to the ETH1-4 uplink port on user’s hub/switch, using a RJ-45 cable WIFI Switch the wireless function on or off RESET...
Wireless ADSL Router USER MANUAL 3 Hardware Installation This chapter shows user how to connect Router. Meanwhile, it introduces the appropriate environment for the Router and installation instructions. Using a telephone line to connect the DSL port of ROUTER to the Modem port of the splitter, and using a other telephone line connect user’s telephone to the PHONE port of the splitter, then connect the wall phone jack to the LINE port of the splitter.
Wireless ADSL Router USER MANUAL 4 PC Configuration Guide Local PC Configuration in Windows 95, 98, ME, XP,VISTA,7 In the Windows task bar, click the “Start” button, point to “Settings”, and then click “Control Panel”. Double-click the “Network” icon. On the “Configuration” tab, select the TCP/IP network associated with user’s network card and then click “Properties”.
Wireless ADSL Router USER MANUAL 5 Web-based Management Guide In order to use the web-based management software it will be necessary to use a computer that occupies the same subnet as the Router. The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router. 5.1 LAN setting page Launch a web browser, such as Internet Explorer, and then use http://192.168.1.1...
Wireless ADSL Router USER MANUAL We can select wizard setup or advanced setup mode to setup KW58283.the wizard set up will guide us for a basic setting,and the advanced setup will guide us to home page for more detailed setup.
Page 14
Wireless ADSL Router USER MANUAL 3. Click WAN Service from Advanced Setup. 4. Click Add to select a layer 2 interface for this service and then click Next. Choose WAN service type, just choose PPPoE for example here. You can enter your own service description here if you want and then click Next.
Page 15
Wireless ADSL Router USER MANUAL 5. Input PPP Username & PPP Password and then click Next. The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password. PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter.
Page 16
Wireless ADSL Router USER MANUAL Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE.
Page 17
Wireless ADSL Router USER MANUAL Use static IPv4 IP address, If the ISP gave you a static IP address, select this option and enter it in the IP address field. Bridge PPPoE Frames Between WAN and Local Ports is available when you do not use PPP IP extension.
Page 18
Wireless ADSL Router USER MANUAL 5.2.2 Router Mode Setup 1. From Advanced Setup, click Layer2 Interface and select ETH Interface. Before you configure ETH WAN interface, you’d better remove all PVC settings from ATM interface. 2. Click Add and you’ll see the following screen.
Page 19
Wireless ADSL Router USER MANUAL 3. Select a ETH port as you will. You can select ENET1, ENET2, ENET3 or ENET4 port as the WAN interface and Default Mode as connection mode. 4. Click Apply/Save and you’ll see the following screen. From Advanced Setup, click WAN Service to configure a WAN service over the interface you selected.
Page 20
Wireless ADSL Router USER MANUAL 8. Enter the user name and password that your ISP has provided to you. Click Next. PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter.
Page 21
Wireless ADSL Router USER MANUAL Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE.
Page 22
Wireless ADSL Router USER MANUAL 10. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses. Click Next. 11. Make sure that the settings below match the settings provided by your ISP. Click on the Apply/Save button to save your configurations and reboot the ADSL router.
Page 23
Wireless ADSL Router USER MANUAL 5.2.3 LAN Settings From LAN, Configure the DSL Router’s IP Address and Subnet Mask for LAN interface. In this page, you can use DHCP (Dynamic Host Configuration Protocol) to control the assignment of IP addresses on your local network (LAN only). support IPv4 /IPv6 dual stack.
Page 24
Wireless ADSL Router USER MANUAL DHCP server not disable the DHCP server unless you wish to let another device handle IP address issuance on the local network. Start / end IP This is the beginning and ending range for the DHCP server address addresses.
Page 25
Wireless ADSL Router USER MANUAL 5.2.3.2 IPv6 LAN Settings Item Description This is the IP address that other devices on your local network will IPv6 address use to connect to the modem. Subnet mask This defines the size of your network. The default is 255.255.255.0. IGMP Snooping is a method that actually “snoops”...
Page 26
Wireless ADSL Router USER MANUAL Use standard mode to flood unknown multicast traffic. Use blocking mode to discard unknown multicast traffic. The DHCP server assigns an IP addresses from a pre-set pool of addresses upon request from DHCP client (e.g. your computer). Do Disable / Enable DHCP server not disable the DHCP server unless you wish to let another device...
Enter a name for user’s wireless network here. SSID stands for Service Set Identifier. This name must be between 1 and 32 characters long. The default Network name (SSID) name is Kasdaxxxx (xxxx means the last 6 number mac address of KW58283 with uppercase and without colon) .
Page 28
Wireless ADSL Router USER MANUAL All wireless clients must either detect the gateway or be configured with the correct SSID to access the Internet. BSSID Displays the gateway's wireless MAC address. (User may need this address if user is using WDS or multiple gateways.) Click Apply to save changes. Drop-down menu that allows selection of specific channel.
Page 29
Wireless ADSL Router USER MANUAL Warning: The settings shown above are default settings. Changes made to these items can cause wireless communication problems. Field Description This is the range of frequencies the gateway will use to communicate with Band user’s wireless devices. Channel Drop-down menu that allows selection of specific channel.
Page 30
Wireless ADSL Router USER MANUAL countdown informing wireless clients of the next window for listening to broadcast and multicast messages. When the gateway has broadcast or multicast messages for its clients, it sends its next DTIM message with this DTIM interval value. The clients hear the beacons and awaken as needed to receive the broadcast and multicast messages.
Page 31
Wireless ADSL Router USER MANUAL 5.3.3 Security This page allows you to configure security features of the wireless LAN interface. You may set up configuration manually or through WiFi Protected Setup(WPS) 1. Click Security of Wireless item and you’ll see the following page. 2.Configure WPA Pre-shared key as below and click Apply/Save.
Page 32
Wireless ADSL Router USER MANUAL 3.Enable WPS as below. 4.Set WPS AP mode as Unconfigured and click Config AP. 5. Set WPS AP mode as configured and click Save/Apply. 6.Now you can use a wireless adaptor with WPS function and the WPS button to connect to access the Internet.
Page 33
Wireless ADSL Router USER MANUAL following information carefully. The wireless security page allows user to configure the security features of user’s wireless network. There are several security methods to choose from, depending on user’s needs and the capabilities of user’s wireless machines. WEP open and WEP shared —WEP is an encryption scheme that is used to ...
Wireless ADSL Router USER MANUAL WPA (PSK) — This is WPA encryption combined with a pre-shared key (PSK), which is a text string known only to the gateway and authorized wireless clients. The gateway rejects the login if the client's PSK does not match. WPA2 —...
Page 35
Wireless ADSL Router USER MANUAL 3.Click Apply/Save and select Device Info=>WAN. You can see the IP address of WAN interface 4.Now you can access the ADSL router remotely using username support and password support. You can input http://x.x.x.x/ for Http and input telnet x.x.x.x for Telnet.
Page 36
Wireless ADSL Router USER MANUAL 5.4.3 Printer Server Installations 1. Click “Advanced setupPrint Server” and then Check “Enable on-board printer server” and key in “Printer name”, “Make and model” . 2. Click on Add a printer from Control Panel of the Windows computer and click “Next”.
Page 37
Wireless ADSL Router USER MANUAL 3. Select “Network Printer” and click “Next”. 4. Select Connect to a printer on the Internet, type “http://192.168.1.1:631/printers/printer” and click “Next”. The printer name “Printer” must be the same name entered in the ADSL router “print server setting” as in step...
Page 38
Wireless ADSL Router USER MANUAL Select driver file directory on CD-ROM or in your hard disk and click “OK”. 6. Choose “Yes” or “No” for default printer setting and click “Next”. Click “Finish”.
Wireless ADSL Router USER MANUAL Appendix: Frequent Asked Questions Q: None of the LEDs are on when user power on the ADSL router? A: Please make sure what user use is the power adaptor attached with the ADSL router package,and check the connection between the AC power and ADSL router. Q: DSL LED does not turn on after connect telephone line? A: Please make sure what user use is the standard telephone line (as attached with the package), make sure the line is connected correctly and check whether there is poor...
Page 40
Wireless ADSL Router USER MANUAL Q: PC cannot browse Internet web page? A: Please make sure DNS server appointed to the PC is correct. User can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator.
Need help?
Do you have a question about the KW58283 and is the answer not in the manual?
Questions and answers