1. Manuals
  2. Brands
  3. Kasda Manuals
  4. Network Router
  5. KW5225
  6. User manual

Kasda KW5225 User Manual

Vdsl
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
KW5225 Wireless VDSL Router
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KW5225 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Kasda KW5225

Summary of Contents for Kasda KW5225

  • Page 1 KW5225 Wireless VDSL Router User Manual...
  • Page 2 WLAN VDSL Gateway User Manual NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.

  • Page 3: Table Of Contents

    WLAN VDSL Gateway User Manual Content OVERVIEW ..........................2 ......................... 2 EATURES ......................4 ACKET ONTENTS ....................5 YSTEM EQUIREMENTS ......................5 ACTORY EFAULTS ....................5 ARNINGS AND AUTIONS HARDWARE DESCRIPTION ....................6 HARDWARE INSTALLATION ....................8 PC CONFIGURATION GUIDE ..................... 9 95, 98, ME, XP ...........

  • Page 4: Overview

    User Manual 1 Overview Thank you for choosing our product. The KW5225 is a Wireless VDSL router combining an VDSL modem, an 802.11g wireless router, a 4-port switch, a printer server host port, bringing high-speed wireless Internet connection to a home or office.
  • Page 5 WLAN VDSL Gateway User Manual 1.1.4 Network Protocol & Features  Ethernet to ADSL Self-Learning Transparent Bridging  Internet Control Message Protocol (ICMP)  IP Static Routing  Routing Information Protocol (RIP, RIPv2)  Network Address Translation (NAT)  Virtual Server, Port Forwarding ...

  • Page 6: Packet Contents

    WLAN VDSL Gateway User Manual  Packet Filtering  Stateful Packet Inspection (SPI)  Denial of Service Prevention (DoS)  1.1.7 Management Support  Web Based GUI  Upgrade or update via FTP/HTTP  Command Line Interface via Telnet  Diagnostic Test ...

  • Page 7: System Requirements

    WLAN VDSL Gateway User Manual System Requirements Before using this ROUTER, verify that you meet the following requirements:  Subscription for ADSL service. Your ADSL service provider should provide you with at least one valid IP address (static assignment or dynamic assignment via dial-up connection).

  • Page 8: Hardware Description

    WLAN VDSL Gateway User Manual 1 Hardware Description Front Panel Color Function On: Power on Green Off: No power On: LAN link established and active via LAN port ETH1-4 Green Blinking: ADSL data activity occurs Off: No LAN link via LAN port On: LAN link established and active via LAN port Green Blinking: ADSL data activity occurs...
  • Page 9 WLAN VDSL Gateway User Manual Rear panel Port Function Connect the device to an ADSL telephone jack or splitter using a RJ-11 telephone cable Connect the device to user’s PC’s Ethernet port,or to the uplink port on user’s hub/switch, using a RJ-45 cable Connect the device to your PC's Ethernet port, or to the ETH1-4 uplink port on user’s hub/switch, using a RJ-45 cable...

  • Page 10: Hardware Installation

    WLAN VDSL Gateway User Manual 3 Hardware Installation This chapter shows you how to connect Router. Meanwhile, it introduces the appropriate environment for the Router and installation instructions. Using a telephone line to connect the DSL port of ROUTER to the MODEM port of the splitter, and using a other telephone line connect your telephone to the PHONE port of the splitter, then connect the wall phone jack to the LINE port of the splitter.

  • Page 11: Pc Configuration Guide

    WLAN VDSL Gateway User Manual PC Configuration Guide Local PC Configuration in Windows 95, 98, ME, XP 1. In the Windows task bar, click the “Start” button, point to “Settings”, and then click “Control Panel”. 2. Double-click the “Network” icon. 3.

  • Page 12: Web-Based Management Guide

    WLAN VDSL Gateway User Manual 5 Web-based Management Guide In order to use the web-based management software it will be necessary to use a computer that occupies the same subnet as the Router. The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router. 5.1 LAN setting page Launch a web browser, such as Internet Explorer, and then use http://192.168.1.1...

  • Page 13: Internet Access Configuration

    WLAN VDSL Gateway User Manual We can select wizard setup or advanced setup mode to setup KW5225.the wizard set up will guide us for a basic setting,and the advanced setup will guide us to home page for more detailed setup.
  • Page 14 WLAN VDSL Gateway User Manual 3. Click WAN Service from the left menu. 4. Click Add to select a layer 2 interface for this service and then click Next. 5. Choose WAN service type, just choose PPPoE for example here. You can enter your own service description here if you want and then click Next.
  • Page 15 WLAN VDSL Gateway User Manual 6. Input PPP Username & PPP Password and then click Next. The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password.
  • Page 16 WLAN VDSL Gateway User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE.
  • Page 17 WLAN VDSL Gateway User Manual Select a preferred wan interface as the system default gateway. 8. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses. If only a single PVC with IPoA or static MER protocol is configured, you must enter static DNS server IP addresses.
  • Page 18 WLAN VDSL Gateway User Manual 5.2.2 VDSL Setup From home page, you can find Advanced Setup option on the left router configuration page. 1. From Layer2 Interface, click PTM Interface. you can set it up according to the following steps. You Choose Add, or Remove to configure DSL PTM interfaces.
  • Page 19 WLAN VDSL Gateway User Manual 5. Choose WAN service type, just choose PPPoE for example here. You can enter your own service description here if you want and then click Next. 6.Input PPP Username & PPP Password and then click Next. The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password.
  • Page 20 WLAN VDSL Gateway User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary. The default value for MTU (Maximum Transmission Unit) is 1500 for PPPoA and 1492 for PPPoE.
  • Page 21 WLAN VDSL Gateway User Manual 7. Select a preferred wan interface as the system default gateway. 8. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses. If only a single PVC with IPoA or static MER protocol is configured, you must enter static DNS server IP addresses.
  • Page 22 WLAN VDSL Gateway User Manual 5.2.3 Router Mode Setup 1. From Advanced Setup, click Layer2 Interface and select ETH Interface. Before you configure ETH WAN interface, you’d better remove all PVC settings from ATM interface. 2. Click Add and you’ll see the following screen. 3.
  • Page 23 WLAN VDSL Gateway User Manual 6. Click Add and you’ll see the following screen. 7. Click Next and you’ll see the following screen. Select PPPoE as WAN service type for example. Click Next. 8. Enter the user name and password that your ISP has provided to you. Click Next.
  • Page 24 WLAN VDSL Gateway User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter. Authentication method is default to Auto. It is recommended that you leave the Authentication method in Auto, however, you may select PAP or CHAP if necessary.
  • Page 25 WLAN VDSL Gateway User Manual PPPoA and 1492 for PPPoE. Do not change these values unless your ISP asks you The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout.
  • Page 26 WLAN VDSL Gateway User Manual 10. Get DNS server information from the selected WAN interface or enter static DNS server IP addresses. Click Next. 11. Make sure that the settings below match the settings provided by your ISP. Click on the Apply/Save button to save your configurations and reboot the ADSL router.
  • Page 27 WLAN VDSL Gateway User Manual 5.2.4 DSL Bonding Click Advanced Setup > DSL Bonding to display the following screen. Select Enable DSL Bonding to use the DSL bonding and ADSL fallback features. Make sure your ISP supports these functions.

  • Page 28: Wireless Setting

    From LAN, Configure the DSL Router’s IP Address and Subnet Mask for LAN interface. In this page, you can use DHCP (Dynamic Host Configuration Protocol) to control the assignment of IP addresses on your local network (LAN only).KW5225 support IPv4 /IPv6 dual stack. 5.2.4.1 IPv4 LAN Settings Item...
  • Page 29 WLAN VDSL Gateway User Manual 255.255.255.0. IGMP Snooping is a method that actually “snoops” or inspects IGMP traffic on a switch. When enabled, the switch will watch for IGMP messages passed between a host and a router, and will add the necessary ports to its multicast table, ensuring that only Enable IGMP the ports that require a given multicast stream actually receive it.
  • Page 30 WLAN VDSL Gateway User Manual 5.2.4.2 IPv6 LAN Settings Item Description This is the IP address that other devices on your local network IPv6 address will use to connect to the modem. This defines the size of your network. The default is Subnet mask 255.255.255.0.
  • Page 31 WLAN VDSL Gateway User Manual Use blocking mode to discard unknown multicast traffic. The DHCP server assigns an IP addresses from a pre-set pool of Disable / Enable addresses upon request from DHCP client (e.g. your computer). DHCP server Do not disable the DHCP server unless you wish to let another device handle IP address issuance on the local network.
  • Page 32 Enter a name for user’s wireless network here. SSID stands for Service Set Identifier. This name must be between 1 and 32 characters long. The default name is WLANxxxx (xxxx means the mac address of KW5225 with Network name (SSID) uppercase and without colon) .
  • Page 33 WLAN VDSL Gateway User Manual Country Drop-down menu that allows selection of specific channel. 5.3.2 Advanced Settings This page is where user specifies a number of advanced settings for wireless communications. Note: After making any changes, click Apply to save. Warning: The settings shown above are default settings.
  • Page 34 WLAN VDSL Gateway User Manual user’s wireless devices. Channel Drop-down menu that allows selection of specific channel. This drop-down list lets user specify the wireless communication rate, which Rate can be Auto (uses the highest rate when possible, or else a lower rate) or a fixed rate between 1 and 54 Mbps.
  • Page 35 WLAN VDSL Gateway User Manual value between 1 and 65535, but the recommended range is 1 - 1000. 5.3.3 Security This page allows you to configure security features of the wireless LAN interface. You may set up configuration manually or through WiFi Protected Setup(WPS) 1.Click Security of Wireless item and you’ll see the following page.
  • Page 36 WLAN VDSL Gateway User Manual 4.Set WPS AP mode as unconfigured and click Config AP. 5. Set WPS AP mode as configured and click Save/Apply. 6.Now you can use a wireless adaptor with WPS function and the WPS button to connect to access the Internet.
  • Page 37 WLAN VDSL Gateway User Manual wireless network. There are several security methods to choose from, depending on user’s needs and the capabilities of user’s wireless machines. WEP open and WEP shared —WEP is an encryption scheme that is used  to protect user’s wireless data communications.
  • Page 38 WLAN VDSL Gateway User Manual WPA — WPA is a more recent encryption method that addresses many of  the weaknesses in WEP. Any client capable of WPA encryption should use it instead of WEP. WPA (PSK) — This is WPA encryption combined with a pre-shared key ...

  • Page 39: Management

    WLAN VDSL Gateway User Manual 5.4 Management 5.4.1 Remote Access When the firewall is enabled on a WAN or LAN interface, all incoming IP traffic is BLOCKED. However, some IP traffic can be ACCEPTED by setting up filters. 1. Select Advanced Setup=>Security=>IP Filtering=>Incoming and Choose Add or Remove to configure incoming IP filters.
  • Page 40 WLAN VDSL Gateway User Manual 5.4.2 TR-069 Client WAN Management Protocol (TR-069) allows a Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Inform: Whether or not the CPE must periodically send CPE information to Server using the Inform method call.
  • Page 41 WLAN VDSL Gateway User Manual username is used only for authentication of the CPE. Connection Request Password: Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for authentication of the CPE. GetRPCMethods: Used by a CPE or ACS to discover the set of methods supported by the ACS or CPE it is in communicate with.
  • Page 42 WLAN VDSL Gateway User Manual 4. Select Connect to a printer on the Internet, type “http://192.168.1.1:631/printers/printer” and click “Next”. The printer name “Printer” must be the same name entered in the ADSL router “print server setting” as in step 1. Select driver file directory on CD-ROM or in your hard disk and click “OK”.
  • Page 43 WLAN VDSL Gateway User Manual Click “Finish”.

  • Page 44: Appendix: Frequent Asked Questions

    WLAN VDSL Gateway User Manual Appendix: Frequent Asked Questions Q: None of the LEDs are on when you power on the ADSL router? A: Please make sure what you use is the power adaptor attached with the ADSL router package and checks the connection between the AC power and ADSL router.
  • Page 45 WLAN VDSL Gateway User Manual Q: PC cannot browse Internet web page? A: Please make sure DNS server appointed to the PC is correct. You can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator.

Table of Contents