Digital View 41755002X-3 Instructions Manual
  1. Manuals
  2. Brands
  3. Digital View Manuals
  4. Controller
  5. 41755002X-3
  6. Instructions manual

Digital View 41755002X-3 Instructions Manual

Dvi, display port, hdmi, video interface controller for tft panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DVI, DISPLAY PORT, HDMI, VIDEO INTERFACE CONTROLLER
CONTENTS
Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer
3. System design - Diagram of a suggested system
5. Assembly notes - Important information about system elements
7. Connection & Operation - How to use the controller
13. Connectors, pinouts & jumpers - Essential connection information
61. Warranty, Caution & Limitation of Liability, Trademarks
It is essential that these instructions are read and understood before connecting or
powering up this controller.
Specifications subject to change without notice
© Digital View Ltd - Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc)
FOR TFT PANEL
Model: SVX-4096
Part number : 41755002X-3 or up
INSTRUCTIONS
gamma LUT
Page 1 of 63

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 41755002X-3 and is the answer not in the manual?

Questions and answers

Related Manuals for Digital View 41755002X-3

Summary of Contents for Digital View 41755002X-3

  • Page 1: Table Of Contents

    63. Revision History It is essential that these instructions are read and understood before connecting or powering up this controller. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 1 of 63...
  • Page 2 Check power settings to all component parts before connection. • DISCLAIMER There is no implied or expressed warranty regarding this material. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 2 of 63...
  • Page 3 SYSTEM DESIGN A typical LCD based display system utilizing this controller is likely to comprise the following: Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 3 of 63...
  • Page 4 Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 4 of 63...
  • Page 5 Panel cable: In order to provide a clean signal it is recommended that all panel cables (V-by-One signal, eDP and LVDS) supplied by Digital View. Care should be taken when placing the cables to avoid signal interference. Inverter/Backlight driver: This will be required for the backlight of an LCD, some LCD panels have an inverter/backlight driver built in.
  • Page 6 • Non-interlaced & interlaced video input is acceptable. • IMPORTANT: Please read the Application Notes section for more information. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 6 of 63...
  • Page 7 Once the system has been connected and switched on there are a number of functions available to adjust the display image as summarized in the following sections. The settings chosen will be saved for each mode independently. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 7 of 63...
  • Page 8 P/N 426123010-3. * Sequence of Input source selection (Press "+" Button to change source, Press "SEL DN" to confirm) Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 8 of 63...
  • Page 9 5800 3200 sRGB User : R [0-255] G [0-255] B [0-255] Color Effect: Standard [Default] Game Movie Photo Vivid Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 9 of 63...
  • Page 10 Backlight Brightness Contrast Sharpness Saturation Aspect Ratio Display Mode Input Swap PIP Size Auto Adjust Volume No Function [Default] Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 10 of 63...
  • Page 11 [Default 50] Language Transparency [0-255] [Default 0] Rotate: 0 [Default 0] Border Width: [0-10] [Default 0] Border Color: R [Default] Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 11 of 63...
  • Page 12 Pin 22 : Low [Default] High Pin 23 : Low [Default] High Pin 24 : Low [Default] High EDID Setup : Reset Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 12 of 63...
  • Page 13 (Matching OSD switch mount cable P/N 426122200-3 (150mm) or 426122210-3 (250mm) Reserved Reserved Infra-red sensor connector JST 3-way, B3B-XH-A (Matching type : XHP-3) Ethernet RJ-45 connector Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 13 of 63...
  • Page 14 Config Menu button (for Ethernet Tact switch button function) Panel selection 8-way DIP Switch Function selection 6-way DIP Switch Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 14 of 63...
  • Page 15 JA15 is set to OPEN) Input power control Short = External switch control and fix the board ON Open = Switch mount control Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 15 of 63...
  • Page 16 ** Ensure that the backlight inverter supports 24V operation prior to connecting a 24VDC input. Because CNA1 pin 1 and CNB1 pin 2 will output 24VDC if input 24VDC via PP5 or PP2. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 16 of 63...
  • Page 17 JA3, JA5 & JA6 location on board : (Please pay attention to the jumper settings on JA3, JA5 & JA6 which are red in color) JA3, JA6 & JA5 Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 17 of 63...
  • Page 18 Note: For setting definition, please refer to V-by-One's pin#15 to pin#24 of panel specification. Remark * Effective on V1.07.00.00 version or up. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 18 of 63...
  • Page 19 CN6 – Light sensor connector : DF13 2-ways (Matching type : DF13-2S-1.25C) SYMBOL DESCRIPTION SENSOR Light sensor input +3.3V Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 19 of 63...
  • Page 20 CN15 – Power connector for IE-2000: Yeonho SMH200-04 (Matching type: SMH200-04) SYMBOL DESCRIPTION 12/24VA +12/24 VDC 12/24VA +12/24 VDC Ground Ground Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 20 of 63...
  • Page 21 MENU OSD menu -/LEFT OSD -/Left +/RIGHT OSD +/Right SEL_DN OSD Select down SEL_UP OSD Select up No connection Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 21 of 63...
  • Page 22 Negative differential LVDS data bit A1 LVDS_OUT3_A0+ Positive differential LVDS data bit A0 LVDS_OUT3_A0- Negative differential LVDS data bit A0 Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 22 of 63...
  • Page 23 Negative differential LVDS data bit B1 LVDS_OUT1_B0+ Positive differential LVDS data bit B0 LVDS_OUT1_B0- Negative differential LVDS data bit B0 Ground Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 23 of 63...
  • Page 24 Panel power selected by JA15 DP_TX_33V Power for connector (3.3V 500mA) Ground DPTX_HPD Hot Plug Detect DPTX_AUX_N Auxiliary Channel (negative) Ground Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 24 of 63...
  • Page 25 Panel power supply (selected by JA15 & JP2) PVLCD_High Panel power supply (selected by JA15 & JP2) (1) - (51): Pin# read on panel side. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 25 of 63...
  • Page 26 TMDS Clock– No connection No connection SCL (I²C Serial Clock for DDC) SDA (I²C Serial Data Line for DDC) Ground Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 26 of 63...
  • Page 27 AUX CH (n) Auxiliary Channel (negative) Hot Plug Hot Plug Detect Ground DP_PWR Power for connector (3.3 V 500 mA) Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 27 of 63...
  • Page 28 PP4 – External panel power input: Molex 43045-0400 or compatible (Matching type : Molex 43025-0400 or compatible) DESCRIPTION External panel power Ground External panel power Ground Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 28 of 63...

  • Page 29: Controller Dimensions

    CAUTION: Ensure adequate insulation is provided for all areas of the PCB with special attention to high voltage parts such as the inverter. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 29 of 63...

  • Page 30: Application Notes

    This can then be matched with function controls connected to CNC1 pins 4 & 3 or 5: see table. CNC1 DESCRIPTION VR A VR WIP VR B Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 30 of 63...
  • Page 31 3.6 V 10 K 4.8 V So this circuit could provide Brightness adjust voltage ranging from 0V to 5V. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 31 of 63...

  • Page 32: Troubleshooting

    : V-by-One's LOCKN signal is set LOW by panel when CDR (clock data recovery) taining is done and CDR • is locked. : No V-by-One's signal is detected and locked. • Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 32 of 63...

  • Page 33: Specifications

    12KB Flash (Parameters settings) 16Mb Flash (System program) 2Mb Flash (Web page data) 512KB EEPROM (System settings) 2Kb EEPROM (Video input paramaters) Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 33 of 63...
  • Page 34 For specific panel setup a sample of an LCD may be required (this will be returned) and a copy of the full technical • specifications for the panel from the manufacturer. Re-layout and custom development services are available. • Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 34 of 63...

  • Page 35: Appendix I - Signal Support Modes Table

    1280x1024 75Hz 1360x768 60Hz 1366x768 60Hz 1440x900 75Hz 1600x1200 75Hz 1680x1050 75Hz 1920x1080 60Hz 1920x1200 60Hz 2560x1600 60Hz 3840x2160 30Hz Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 35 of 63...
  • Page 36 3840x2160 23.976Hz 3840x2160 24Hz 3840x2160 25Hz 3840x2160 29.97Hz 3840x2160 30Hz 4096x2160 23.976Hz 4096x2160 24Hz 4096x2160 25Hz 4096x2160 29.97Hz 4096x2160 30Hz Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 36 of 63...
  • Page 37 3840x2160 59Hz 3840x2160 60Hz 4096x2160 23.976Hz 4096x2160 24Hz 4096x2160 25Hz 4096x2160 29.97Hz 4096x2160 30Hz 4096x2160 50Hz 4096x2160 59Hz 4096x2160 60Hz Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 37 of 63...
  • Page 38 3840x2160 59Hz 3840x2160 60Hz 4096x2160 23.976Hz 4096x2160 24Hz 4096x2160 25Hz 4096x2160 29.97Hz 4096x2160 30Hz 4096x2160 50Hz 4096x2160 59Hz 4096x2160 60Hz Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 38 of 63...

  • Page 39: Appendix Ii - Network Connection

    TCP/IP network. (Note: The 3 party program is not warranted nor is it the responsibility of Digital View.) Below are the example of using TCP-COM and serial communication software (e.g. Access Port) to adjust brightness value of SVX-4096 over LAN.
  • Page 40 [Soft power on] 81 36 34 [Adjust brightness to max. value] 98 50 31 [Jump to Display Port input] Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 40 of 63...
  • Page 41 Appendix VII. (Some sensor functions might require alternative firmware version.) For details, please refer to the separate application note. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 41 of 63...

  • Page 42: Appendix Iii - Rs-232 Control Protocols And Command Set

    The RS-232 program can be custom-made to fit for application or it can be used the serial control program, like Accessport, Telix or Serial Utility program developed by DigitalView. Please contact your local support for information. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 42 of 63...
  • Page 43 | “+” | “-” | value/increment/decrement “?” Query Image H position 0x86, Set horizontal position = nn = 0x00~ 0x64 (0~100%) Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 43 of 63...
  • Page 44 Set auto source seek = “0” | “1” | Disable/Enable “r” | “R” | Reset Default: “1” (Enable) “?” Query Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 44 of 63...
  • Page 45 Select PIP window size = select nn | PIP window size value 0x00(smallest)~0x0A (largest) “r” | “R” | Reset Default: 0x0A Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 45 of 63...
  • Page 46 = nn | “+” | “-” | value/increment/decrement “r” | “R” | Reset Default: 0x80 Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 46 of 63...
  • Page 47 “?” Reset 120Hz : “0”,”7”,”8” Query 140Hz : “0”,”8”,”C” 160Hz : “0”,”A”,”0” (Default) 180Hz : “0”,”B”,”4”’ 200Hz : “0”,”C”,”8” Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 47 of 63...
  • Page 48 0x36, nnnn | 0x36=Hsync back porch 0=1ports,1=2ports,2=4ports,3=8ports 0x37, nnnn | 0x37=Display horizontal width 0x38, nnnn | 0x38=Vertical total typical Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 48 of 63...
  • Page 49 Reset to use pre-defined EDID Reset instead of user EDID of selected return "1" Success port return "0" Fail Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 49 of 63...
  • Page 50 Reset all parameters, including “1” - successful. parameters user color temperature setting, for all video modes to default value Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 50 of 63...
  • Page 51 0x71 0x52 0x72 0x53 0x73 0x54 0x74 0x55 0x75 0x56 0x76 0x57 0x77 0x58 0x78 0x59 0x79 0x5A 0x7A Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 51 of 63...

  • Page 52: Appendix Iv - Mapping Definition

    Appendix IV – Mapping definition Definition of division Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 52 of 63...
  • Page 53 Input data mapping Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 53 of 63...

  • Page 54: Appendix V - Dv Remote Control Unit Work For Svx-4096

    1. Toggle between PIP mode and 1P mode. * Sequence of Input source selection (Press "+" Button to change source, Press "SEL DN" to confirm) Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 54 of 63...

  • Page 55: Appendix Vi - Pip Mix Table

    HDMI PIP \ MAIN (P1/CN2) (P2/CN16) (P3/CN5) (P4) (P5) DVI (P1/CN2) HDMI (P2/CN16) HDMI (P3/CN5) HDMI (P4) DisplayPort (P5) Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 55 of 63...

  • Page 56: Appendix Vii - Functions List On Browser Page

    Temperture Monitor (Int. Temp.) Temperture Monitor (Ext. Temp.) Power Monitor (PS 1) Power Monitor (PS 2) Light Monitor (Light1) Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 56 of 63...
  • Page 57 User - Blue Level Color Temp. Value Color Effect Standard/Game/Movie/Photo/Vivid/User Gamma Off/1.8/2.0/2.2/2.4 Advanced Setting Aspect Ratio Full/16:9/4:3/5:4/1:1 Display Orientation Normal/Anti-Clockwise 90/Rotate 180/Anti-Clockwise 270 Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 57 of 63...
  • Page 58 Reset All Parameters Reset all parameters to default value Reset Parameters Reset all parameters for all video mode to defualt value Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 58 of 63...

  • Page 59: Appendix Viii - Renaming Video Input Ports On The Menu And User Defined

    SVX-4096 supports User Gamma function and the user gamma table can be uploaded via TCP/IP Serial Utility program. Please refer to the application note in details. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 59 of 63...

  • Page 60: Appendix Ix - Auto Color Gain

    Reset Color Gain function can be used. This function will reset the stored RGB values to a set of approximate values. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 60 of 63...
  • Page 61 TRADEMARKS The following are trademarks of Digital View Ltd: Digital View • SVX-4096 • Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 61 of 63...

  • Page 62: Contact Details

    6 How Ming St. Kwun Tong Hong Kong Tel: (852) 2861 3615 Fax: (852) 2520 2987 Sales: hksales@digitalview.com WEBSITE www.digitalview.com Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 62 of 63...

  • Page 63: Revision History

    - Add Appendix VIII – Renaming video input ports on the menu and User defined gamma LUT. - Add Appendix IX – Auto Color Gain. Specifications subject to change without notice © Digital View Ltd – Ver 2.6 30 Sept 2021 (SVX-4096_manual.doc) Page 63 of 63...

This manual is also suitable for:

Svx-4096

Table of Contents