Steris Reliance 1024 Uncrating/Installation Instructions
Steris Reliance 1024 Uncrating/Installation Instructions

Steris Reliance 1024 Uncrating/Installation Instructions

Laboratory glassware dryers

Advertisement

UNCRATING/INSTALLATION
INSTRUCTIONS
®
Reliance
1024/1034
Laboratory Glassware Dryers
(10/18/01)
P-122990-608
Rev. 4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Reliance 1024 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Steris Reliance 1024

  • Page 1 UNCRATING/INSTALLATION INSTRUCTIONS ® Reliance 1024/1034 Laboratory Glassware Dryers (10/18/01) P-122990-608 Rev. 4...
  • Page 2 AND HOLD STERIS HARMLESS FROM ANY AND ALL CLAIMS, LIABILITY, DAMAGES, OR EXPENSES DUE TO PERSONAL INJURIES, INCLUDING DEATH, TO EMPLOYEES OF CUS- TOMER AND STERIS AND TO THIRD PARTIES AND FOR PROPERTY DAMAGE TO THE EXTENT CAUSED BY THE WILLFUL ACTS, NEGLIGENCE, OR STRICT LIABILITY OF CUSTOMER.
  • Page 3 (previously furnished), showing all utility service and space require- ments. If drawings cannot be located, replacement copies may be obtained by writing, wiring, faxing, or telephoning STERIS giving the serial, equipment and model numbers of your dryer. If STERIS supervision is desired for installing this equipment, contact the STERIS Regional Office nearest you.
  • Page 4 Please contact your STERIS representative for details. Sales and Service Information: Technical Assistance: STERIS Corporation STERIS Engineering 5960 Heisley Road Services Mentor, Ohio 44060 2424 West 23rd Street Tel.: 440 354 2600...
  • Page 5: Table Of Contents

    TABLE OF CONTENTS SECTION TITLE PAGE LISTING OF WARNINGS, CAUTIONS AND SYMBOLS . 1-1 UNCRATING INSTRUCTIONS ........2-1 Open Crate ..................2-1 Move Dryer and Remove Skid ............2-1 Prepare Dryer for Installation ............2-3 INSTALLATION INSTRUCTIONS ......... 3-1 Before Installing Equipment ............3-1 Connect Utilities ................
  • Page 6: Listing Of Warnings, Cautions And Symbols

    LISTING OF WARNINGS, CAUTIONS AND SYMBOLS The following is a listing of the safety precautions which must be observed when uncrating, installing and operating this equipment. WARNINGS indicate the potential for danger to personnel, and CAUTIONS indicate the potential for damage to equipment. These precautions are repeated in whole or in part, throughout the instructions. WARNING - PERSONAL INJURY AND/OR EQUIPMENT DAMAGE HAZARD: When moving the unit, use a forklift.
  • Page 7 Symbols Tip'N Tell Indicator Attention, Consult Manual for Further Instructions This Way Up Do Not Stack Fragile Keep Dry Amperage Rating of the Unit Voltage Rating of the Unit Alternating Current Power Rating of the Unit Frequency of the Unit Phase of the Unit 122990-608 Uncrating/Installation Instructions...
  • Page 8: Uncrating Instructions

    If unit has been tipped, residue from the blue compound will be found higher up in the indicator. If unit was tipped, notify STERIS regional office. A service technician will review the equipment and determine if unit was damaged.
  • Page 9 Bands Cardboard Nails Figure 2-1. Crate Blower Tip Indicator Electrical Box Thermostat Identification Ref.: 920-001-974 Nameplate Figure 2-2. Check Tip Indicator 122990-608 Uncrating/Installation Instructions Uncrating Instructions...
  • Page 10: Prepare Dryer For Installation

    1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 1.
  • Page 11 Shelf Support Strip Adjustable Non-adjustable Shelves Shelf Guide Tab Chamber Bottom Plate Figure 2-4. Drying Chamber 122990-608 Uncrating/Installation Instructions Uncrating Instructions...
  • Page 12: Installation Instructions

    Utility service lines: • If unit is equipped with steam option, shutoff valve (not by STERIS) should be installed on steam line near dryer (see Figure 3-1). Shutoff valve must be capable of being locked in OFF position.
  • Page 13: Cleanup

    (in same direction as sur- THIS COMPLETES THE INSTALLATION. Contact your local face grain). Solvent rubbed in a cir- STERIS representative for a demonstration on how to operate the cular motion or applied with a wire equipment. Refer to Operator Manual (P-122990-607) for operating brush or steel wool on door and procedures.
  • Page 14: Operational Test

    OPERATIONAL TEST 1. Open chamber door(s). 2. Check that drying chamber is empty and all packing material has been removed. 3. If unit is equipped with manifold drying option, verify that manifold connectors are installed. 4. Close door and press START pushbutton (see Figure 4-1). 5.

This manual is also suitable for:

Reliance 1034

Table of Contents