Advertisement
USING POWERSCAN™ D8340 SERIES READERS
PowerScan™ D8340 readers automatically scan barcodes at a distance. Simply aim and
pull the trigger. Code scanning is performed along the scan line emitted from the reading
window. This line must cross the entire code. The best reading angles are indicated in the
figure below.:
TECHNICAL FEATURES
PowerScan™ D8340/ D8340 AR
PowerScan™ D8330
Electrical Features
PowerScan™ D8330
AR
4 to 30 VDC
Power Supply
Max. Consumption:
0.076 mm (3 mils)
0.25 mm (10 mils)
@ 4V
420 mA
500 mA
@5V
310 mA
370 mA
@30V
62 mA
70 mA
Sleep mode
4 mA
4 mA
Scan Rate
35 ± 5 scans/sec
Good Read LED (green)
Reading Indicators
Good Read Spot (green), Beeper
Optical Features
Reading Field
97.8 cm (38.5 in)
12.5 m (41.0 ft)
(Typical performance at 20ºC / 68ºF
@ 40 mils
@ 100 mils reflective
on high quality barcodes)
Max. Resolution
0.076 mm (3 mils)
0.178 (7,5 mils)
PCS (Datalogic Test Chart)
15%
25%
Laser Features
Power (max)
0.9 mW
1.3 mW
Scan Angle
42°
13.5° ± 0.7
Laser Safety Class
Class 2 EN 60825-1/CDRH
Environmental Features
Working Temperature
-30 °C to + 50 °C / -22° to +122 °F
Storage Temperature
-30 °C to + 70 °C / -22° to +158 °F
Humidity
90% non condensing
Drop Resistance
IEC 68-2-32 Test ED 2 m
Protection Class
IP65
Mechanical Features
Weight (without cable)
about 295 g (10.4 oz)
Cable Length
2 m (6 ft 6 in)
ELECTRICAL CONNECTIONS
The PowerScan™ D8340/D8340 AR scanner can be used with CAB 468 (coiled cable and
9-pin male connector) for direct connection to the DATAPLUS and DLD series decoders.
CAB 468
1 - Not connected
5 - TRIGGER
1
2
3
4
5
2 - SCAN
6 - BEEPER/LED
3 - Not connected
7 - VIDEO
9
6
7
8
4 - GND
8 – LASER ON
9 - +VCC
9-pin male connector
A definition of the terms used to identify the pins is as follows:
SCAN
This scanner "open collector" output signal is used to synchronize the
decoding logic with the scanner. Each transition of this signal from
low-to-high or high-to-low corresponds to the start of a scan. The
signal is a TTL level 57 ms period square wave (see the following figure
Video and Scan signals).
GND
Supply ground and signal reference.
TRIGGER
This output is connected to GND when the trigger is pressed and is left
floating when the trigger is released.
BEEPER/LED
This scanner input drives the green decoding LED, and the beeper in
the scanner. The LED turns on when a positive current is applied to the
pin. The beeper sound is obtained pulsating this current at a
frequency of about 2 kHz. The maximum voltage that can be applied
to this input is 5 VDC.
VIDEO
This "open collector" scanner output is electrically identical to the
barcode. It supplies a series of pulses the length of which are
proportional to the width of the elements within the barcode read. A
low output level corresponds to a bar. The frequency of the pulses
depends on the density of the code, the distance from code and the
programmed output scan frequency (see the following figure Video
and Scan signals).
LASER ON
A positive voltage between 4.75 and 5 VDC is applied to this input by
the decoder when the decoding logic senses the trigger is pressed;
this causes the laser to start scanning and the red LED to turn on.
+VCC
This input must be connected to the positive pin of the supply voltage
(4.75 - 14 VDC). When the LASER ON pin is positive, all the current
necessary to power the scanner flows through +VCC.
Video and Scan Signals
DATALOGIC SCANNING LIMITED FACTORY WARRANTY
Warranty Coverage
Datalogic warranties this product against defects in workmanship and materials, for a
period of 3 years from the date of shipment, provided that the product is operated under
normal and proper conditions.
Datalogic Scanning ("Datalogic") hardware products are warranted against defects in
material and workmanship under normal and proper use. The liability of Datalogic under
this warranty is limited to furnishing the labor and parts necessary to remedy any defect
covered by this warranty and restore the product to its normal operating condition. Repair
or replacement of product during the warranty does not extend the original warranty
term. Products are sold on the basis of specifications applicable at the time of manufacture
and Datalogic has no obligation to modify or update products once sold.
If Datalogic determines that a product has defects in material or workmanship, Datalogic
shall, at its sole option repair or replace the product without additional charge for parts
and labor, or credit or refund the defective products duly returned to Datalogic. To per-
form repairs, Datalogic may use new or reconditioned parts, components, subassemblies
or products that have been tested as meeting applicable specifications for equivalent new
material and products. Customer will allow Datalogic to scrap all parts removed from the
repaired product. The warranty period shall extend from the date of shipment from Data-
logic for the duration published by Datalogic for the product at the time of purchase (War-
ranty period). Datalogic warrants repaired hardware devices against defects in
workmanship and materials on the repaired assembly for a 90 day period starting from the
date of shipment of the repaired product from Datalogic or until the expiration of the orig-
inal warranty period, whichever is longer. Datalogic does not guarantee, and it is not
responsible for, the maintenance of, damage to, or loss of configurations, data, and appli-
cations on the repaired units and at its sole discretion can return the units in the "factory
default" configuration or with any software or firmware update available at the time of the
repair (other than the firmware or software installed during the manufacture of the prod-
uct). Customer accepts responsibility to maintain a back up copy of its software and data.
Warranty Claims Process
In order to obtain service under the Factory Warranty, Customer must notify Datalogic of
the claimed defect before the expiration of the applicable Warranty period and obtain
from Datalogic a return authorization number (RMA) for return of the product to a desig-
nated Datalogic service center. If Datalogic determines Customer's claim is valid, Datalogic
will repair or replace product without additional charge for parts and labor. Customer shall
be responsible for packaging and shipping the product to the designated Datalogic ser-
vice center, with shipping charges prepaid. Datalogic shall pay for the return of the prod-
uct to Customer if the shipment is to a location within the country in which the Datalogic
service center is located. Customer shall be responsible for paying all shipping charges,
duties, taxes, and any other charges for products returned to any other locations. Failure
to follow the applicable RMA policy, may result in a processing fee. Customer shall be
responsible for return shipment expenses for products which Datalogic, at its sole discre-
tion, determines are not defective or eligible for warranty repair.
Warranty Exclusions
The Datalogic Factory Warranty shall not apply to:
(i)
any product which has been damaged, modified, altered, repaired or upgraded
by other than Datalogic service personnel or its authorized representatives;
(ii) any claimed defect, failure or damage which Datalogic determines was caused
by faulty operations, improper use, abuse, misuse, wear and tear, negligence,
improper storage or use of parts or accessories not approved or supplied by
Datalogic;
(iii) any claimed defect or damage caused by the use of product with any other
instrument, equipment or apparatus;
(iv) any claimed defect or damage caused by the failure to provide proper
maintenance, including but not limited to cleaning the upper window in
accordance with product manual;
(v) any defect or damage caused by natural or man-made disaster such as but not
limited to fire, water damage, floods, other natural disasters, vandalism or
abusive events that would cause internal and external component damage or
destruction of the whole unit, consumable items;
(vi) any damage or malfunctioning caused by non-restoring action as for example
firmware or software upgrades, software or hardware reconfigurations etc.;
(vii) the replacement of upper window/cartridge due to scratching, stains or other
degradation and/or
(viii) any consumable or equivalent (e.g., cables, power supply, batteries, keypads,
touch screen, triggers etc.).
No Assignment
Customer may not assign or otherwise transfer its rights or obligations under this warranty
except to a purchaser or transferee of product. No attempted assignment or transfer in vio-
lation of this provision shall be valid or binding upon Datalogic
DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, ORAL OR WRITTEN, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITA-
TION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PUR-
POSE, OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE FOR ANY DAMAGES
SUSTAINED BY CUSTOMER ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF
PRODUCTS UNDER THE ABOVE. THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT
IS THE CUSTOMER'S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY CLAIMS. UNDER NO
CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR
ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CON-
TINGENT DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE NOTICE OF
THE POSSIBILITY OF SUCH DAMAGES.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic
shall assume risk of loss or damage for product in Datalogic's possession. In the absence of
specific written instructions for the return of product to Customer, Datalogic will select the
carrier, but Datalogic shall not thereby assume any liability in connection with the return
shipment.
Advertisement
