Related Manuals for Datalogic PowerScan PD9130
Summary of Contents for Datalogic PowerScan PD9130
- Page 1 PowerScan™ PD9130 Industrial Corded Handheld Linear Imager Bar Code Reader Quick Reference Guide...
- Page 2 Datalogic has taken reasonable measures to provide informa- tion in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A.
-
Page 3: Table Of Contents
Resetting Product Defaults ..........15 Reading Parameters ..............16 Good Read Green Spot Duration ........16 Aiming Pointer ................17 Technical Specifications ............18 LED and Beeper Indications ............21 Cleaning ..................24 Datalogic Limited Factory Warranty ........25 Ergonomic Recommendations ..........27 Support Through the Website ..........28 Quick Reference Guide... - Page 4 NOTES PowerScan™ PD9130...
-
Page 5: End User Software License Agreement (Eula)
2. Scope Of License Granted 2.1 Datalogic grants to End User a personal non-exclusive, non-transferable, per- petual license to use the Software, solely on the Datalogic Product in which it is embedded ("designated Datalogic Product"), in machine-readable form only, solely for End User's internal business purposes. This Agreement does not convey ownership of the Software to End User. - Page 6 3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or other- wise transfer the Datalogic Product to any third party unless such third party agrees with Datalogic in writing to be bound by the terms and conditions of this Agreement. Any such transfer of the Datalogic Product absent such agreement shall be null and void.
- Page 7 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013(c)(1)(ii), whichever is applicable. 9.2 If End User is using the Datalogic Product outside of the United States, End User must comply with the applicable local laws of the country in which the Datalogic Product is used, with U.S.
- Page 8 11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be effective when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of Datalogic IP Tech S.r.l., Legal & IP Department, Via San Vitalino 13, 40012 Calderara di Reno (Bologna), Italy or such other address as may be specified by Datalogic in writing.
-
Page 9: Software Product Policy
Software Product Policy Software Product Policy Datalogic reserves the right to ship its products with the latest version of software/firmware available. This pro- vides our customers with the very latest in Datalogic soft- ware technology. The only exception to this policy is when the buyer has a... - Page 10 Software Product Policy NOTES viii PowerScan™ PD9130...
-
Page 11: Description
PowerScan™ PD9130 Description The PowerScan™ 9130 is a feature-rich and rugged linear imager reader. General Features To read a symbol, you simply aim the reader Operating and pull the trigger. Thanks to powerful algorithms, PowerScan™ PD9130 reliably decodes all major 1D (linear) barcodes. -
Page 12: Connecting The Cable
Setting Up the Reader Connecting the Cable A. Rubber gasket B. Cable Holder C. Cover D. Connector Holder Slip the cable through the Cover. Push the Rubber Gas- ket onto the Cable FRONT>> Holder. Push the Cable Holder and gasket into the handle. -
Page 13: Using The Powerscan™ Pd9130
Using the PowerScan™ PD9130 Using the PowerScan™ PD9130 The PowerScan™ PD9130 normally functions by capturing and decoding bar codes. The reader is equipped with an aiming system which helps to aim the target. PowerScan™ PD9130 provides an aiming system. If enabled, a partial trigger press produces a flashing scan line, which should be aimed over the code, see the figure above. -
Page 14: Reading Angle
If the entire bar code is within the scan line, you will get a good read. Successful reading is signaled by an audible tone plus a good-read green spot LED indicator. Reference the PowerScan PD9130 Product Reference Guide (PRG) for more information about this feature and other programmable settings. -
Page 15: Selecting The Interface Type
Information and programming options for each interface type are provided in this section. For defaults and addi- tional information associated with each interface, proceed to the corresponding chapter in the PowerScan PD9130 PRG. Configuring the Interface Scan the appropriate programming bar code to selects the interface type for your system. - Page 16 Selecting the Interface Type RS-232 RS-232 standard interface RS-232 RS-232 Wincor-Nixdorf RS232-WN RS-232 for use with OPOS/UPOS/JavaPOS RS-232 OPOS PowerScan™ PD9130...
- Page 17 USB Com to simulate RS-232 standard interface USB-COM USB-OEM (can be used for OPOS/UPOS/JavaPOS) USB-OEM a. Download the correct USB Com driver from www.datalogic.com USB Keyboard with standard key encoding USB-KBD USB Keyboard with alternate key encoding USB-KBD-ALT Quick Reference Guide...
-
Page 18: Keyboard Interface
Selecting the Interface Type Keyboard Interface KEYBOARD WEDGE IBM AT or PS/2 PCs Standard Key Encoding KBD-AT IBM AT or PS/2 PCs Standard Key Encoding without external keyboard KBD-AT-NK IBM AT or PS/2 PCs w/Alternate Key KBD-AT-ALT IBM AT or PS/2 PCs Alternate Key Encoding without external keyboard KBD-AT-ALT-NK PowerScan™... -
Page 19: Country Mode
Selecting the Interface Type Country Mode This feature specifies the country/language supported by the keyboard. COUNTRY MODE ENTER/EXIT PROGRAMMING MODE Country Mode = U.S. Country Mode = Belgium Country Mode = Britain Country Mode = Croatia Quick Reference Guide... - Page 20 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Czech Country Mode = Denmark Country Mode = France Country Mode = French Canadian Country Mode = Germany Country Mode = Hungary PowerScan™ PD9130...
- Page 21 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Italy Country Mode = Japanese 106-key Country Mode = Lithuanian Country Mode = Norway Country Mode = Poland Country Mode = Portugal Quick Reference Guide...
- Page 22 Selecting the Interface Type COUNTRY MODE (continued) Country Mode = Romania Country Mode = Spain Country Mode = Sweden Country Mode = Slovakia Country Mode = Switzerland PowerScan™ PD9130...
-
Page 23: Caps Lock State
Selecting the Interface Type Caps Lock State This option specifies the format in which the reader sends character data. This applies to keyboard wedge interfaces. This does not apply when an alternate key encoding key- board is selected. It does not apply to USB keyboard. ENTER/EXIT PROGRAMMING MODE Caps Lock State = Caps Lock OFF Caps Lock State = Caps Lock ON... -
Page 24: Numlock
Interfaces section, select other options and cus- tomize your reader through use of the programming bar codes available in the PowerScan PD9130. Check the cor- responding features section for your interface, and also the Data Editing and Symbologies chapters of the PRG. -
Page 25: Configure Other Settings
Programming like the "Reset Default Settings" on page 16, require only the scan of that single label to enact the change. Other bar codes require the reader to be placed in Pro- gramming Mode prior to scanning them. Scan an ENTER/ EXIT bar code once to enter Programming Mode;... -
Page 26: Reading Parameters
Reading Parameters Reading Parameters Move the reader toward the target and center the aiming, then pull the trigger to capture and decode the barcode. Using the PowerScan™ PD9130 on page 3 for more information. As you read code symbols, adjust the distance at which you are holding the reader. -
Page 27: Aiming Pointer
Aiming Pointer Aiming Pointer Enables / disables the aiming pointer. Aiming pointer = disable Aiming pointer = enable Quick Reference Guide... -
Page 28: Technical Specifications
Technical Specifications Technical Specifications The following table contains Physical and Performance Characteristics, User Environment and Regulatory infor- mation. Physical Characteristics Height: 212 mm Dimensions Length: 110 mm Width: 74 mm Weight (without cable) 340 g Electrical Characteristics Voltage & Current Input Voltage 4.5 / 30 VDC Input Current... - Page 29 Technical Specifications Performance Characteristics Light Source Green LED Roll (Tilt) Tolerance ± 45° Pitch Tolerance ± 75° Skew (Yaw) Toler- ± 70° ance Print Contrast Mini- 15% minimum reflectance Maximum 2.5 mils Resolution Depth of Field (Typical) Symbology: Code 39 5 mils 3 - 32 cm / 1.2 - 12.6”...
- Page 30 Full ASCII, Code39 CIP, Code 32, Codabar, Interleaved 2 of 5, IATA, Industrial 2 of 5, Standard 2 of 5, Code11, MSI, Plessey, Code 93, Follet 2/5, Code 4, Code 5, Datalogic 2 of 5, Codablock F RS-232, Keyboard Wedge, and USB.
-
Page 31: Led And Beeper Indications
LED and Beeper Indications LED and Beeper Indications The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. An optional “Green Spot” also performs useful functions. The following tables list these indications. One exception to the behaviors listed in the tables is that the reader’s func- tions are programmable, and so may or may not be turned on. - Page 32 LED and Beeper Indications Indicator Description Beeper Upon success- ful read of a label, the soft- Green Spot ware shall turn flashes the green spot momentarily on for the time specified by the configured value. Except when in sleep mode or when a Good Read LED Duration other than 00 is selected PowerScan™...
- Page 33 LED and Beeper Indications Programming Mode The following indications ONLY occur when the reader is in Programming Mode INDICATION DESCRIPTION BEEPER Label Pro- A valid program- Reader sounds LED blinks four low fre- gramming ming label has continuously Mode Entry been scanned.
-
Page 34: Cleaning
Cleaning Cleaning Exterior surfaces and scan windows exposed to spills, smudges or debris require periodic cleaning to ensure best performance during scanning. Use a soft, dry cloth to clean the product. If the product is very soiled, clean it with a soft cloth moistened with a diluted non-aggressive cleaning solution or diluted ethyl alcohol. -
Page 35: Datalogic Limited Factory Warranty
Datalogic service center, with shipping charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Da- talogic service center is located. - Page 36 No attempted assignment or transfer in violation of this provision shall be valid or binding upon Datalogic. DATALOGIC' S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, ORAL OR WRITTEN, STATU- TORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT.
-
Page 37: Ergonomic Recommendations
Risk of Loss Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss or damage for product in Datalogic’s possession. In the absence of specific writ- ten instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment. -
Page 38: Support Through The Website
Support Through the Website Support Through the Website Datalogic provides several services as well as technical support through its website. Log on to www.datalogic.com and click on the SUPPORT > Industrial Handheld Scanners category link. From this page you can select your product model from the drop- down list which gives you access to: Downloads including Data Sheets, Manuals, Software &... - Page 39 Support Through the Website NOTES Quick Reference Guide...
- Page 40 ©2017 Datalogic S.p.A. and/or its affiliates. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Datalogic USA Inc. 959 Terry Street | Eugene, OR 97402 | U.S.A. |...