Download Print this page
ICP DAS USA PM-3133i Quick Start Manual

ICP DAS USA PM-3133i Quick Start Manual

Hide thumbs Also See for PM-3133i:

Advertisement

Quick Links

1. Shipping Package
This shipping package contains the following items
1 x PM-3133i module
1.1. Caution & Warning
result in serious injury or death. Any work on or near energized meters,
meter sockets, or other metering equipment could induce a danger of
electrical shock. It is strongly recommended that all work should be
performed only by qualified industrial electricians and metering
specialist. ICP DAS assumes no responsibility if your electrical installer
does not follow the appropriate national and local electrical codes.
ICP DAS assumes no liability for any damage resulting from the use of
this product. ICP DAS reserves the right to change this manual at any
time without notice. The information furnished by ICP DAS is believed
to be accurate and reliable. However, no responsibility is assumed by
ICP DAS for its use, not for any infringements of patents or other rights
of third parties resulting from its use.
ICP DAS Co., LTD
PM-3133i Quick Start
1 x Quick Start
The meter contains hazardous voltages, and should
never be disassembled. Failing to follow this practice will
PM-3133i Quick Start V1.00
Screw Driver x 1
Cable ties x 3
Page 1

Advertisement

loading

Summary of Contents for ICP DAS USA PM-3133i

  • Page 1 PM-3133i Quick Start 1. Shipping Package This shipping package contains the following items 1 x PM-3133i module 1 x Quick Start Screw Driver x 1 Cable ties x 3 1.1. Caution & Warning The meter contains hazardous voltages, and should never be disassembled.
  • Page 2  Please read this operation manual carefully before using.  Please re-confirm the measure position.  Reconfirm the RST (ABC) phase sequence of the power system.  Meter auxiliary power for PM-3133i series is DC +12V ~+48V. ICP DAS Co., LTD PM-3133i Quick Start V1.00...
  • Page 3 2.3. Current Input 1. The external CT’s are fragile, please handle with care. 2. The CT input of PM-3133i-xxxP series is in mV range. Only the ex-factory attached CT’s can be used. The other CT’s, for example, from panel will damage the instrument due to its large current (around 5A or mA).
  • Page 4 <Φ10 use 60A CT,Φ10~Φ16 use 100A CT,Φ16~Φ24 use 200A CT ,Φ24~Φ36 use 300A or 400A CT。 9. The maximum current value cannot exceed the CT rating. ICP DAS Co., LTD PM-3133i Quick Start V1.00 Page 4...
  • Page 5  Open the CT clip. there is a “K→L” mark.  Make sure the power current  Installation steps finished. direction follow the “K→L” mark on the CT and then close the CT clip. ICP DAS Co., LTD PM-3133i Quick Start V1.00 Page 5...
  • Page 6 2.5. Wiring  1P2W-1CT(PM-3133i)  1P3W-2CT(PM-3133i) ICP DAS Co., LTD PM-3133i Quick Start V1.00 Page 6...
  • Page 7  3P3W-3CT(PM-3133i)  3P4W-3CT(PM-3133i) ICP DAS Co., LTD PM-3133i Quick Start V1.00 Page 7...
  • Page 8 125k(Default) 9600 bps 19200 (Default) 250k bps 38400 bps 500k bps 115200 bps 1M bps PM-3133i:Select the different wiring mode (Please select the Software setting, if 1P2W-1CT or 1P3W-2CT is used) Models PM-3133i PM-3133i-MTCP Wiring SW 9 SW 10 SW 1...

This manual is also suitable for:

Pm-3133i-mtcpPm-3133i-240p crPm-3133i-400p crPm-3133i-360p crPm-3133i-160p crPm-3133i-100p cr