Tables - ABB A135-M56 Operation Manual

Operation Manual / 4 Product description / A130-M.. - A145-M..

Tables

Tables
Table 1 Related documents .................
Table 2 Turbocharger weights .............
Table 3 Requirements for threaded rods . 17
Table 4 Tightening torques for stand-
ard nuts ..................................
Table 5 Pressure screw tightening
torques ...................................
Table 6 Lubricating oil pressure, oil inlet
Table 7 Lubricating oil temperature at
the inlet ...................................
Table 8 Lubricating oil temperature at
the outlet .................................
Table 9 Tightening torque (86505) .......
Table 10 Expected replacement intervals
Table 11 Maintenance table ..................
Table 12 Parameters for wet cleaning of
compressor .............................
Table 13 Turbine wet cleaning, recom-
mended operating state ..........
Table 14 Wet cleaning of turbines, pa-
rameters .................................
Table 15 Value table for soaking ...........
Table 16 Malfunctions when starting -
Delayed start-up .....................
Table 17 Malfunctions when starting -
Vibrations ...............................
Table 18 Malfunctions when starting -
Rubbing of rotating parts .........
Table 19 Malfunctions during operation -
Lubricating oil pressure too low
Table 20 Malfunctions during operation
- Speed reduces .....................
Table 21 Malfunctions during operation
- Speed increases ..................
Table 22 Malfunctions during operation
- Exhaust gas temperature too
high.........................................
Table 23 Malfunctions during operation
- Charge air pressure too low .
Table 24 Malfunctions during operation
- Charge air pressure too high
© Copyright 2016 ABB. All rights reserved.
5 Table 25 Malfunctions during operation
- Engine performance losses .. 68
11
Table 26 Malfunction - Turbocharger
pumping .................................. 69
Table 27 Malfunction - Sporadic surge
19
blows ...................................... 69
Table 28 Malfunctions when stopping -
21
Runout noises ......................... 70
29
Table 29 Malfunctions when stopping -
Runout time too short .............. 70
30
Table 30 Malfunction of the speed
measurement system - No
30
signal or poor signal amplitude 71
34
Table 31 Malfunction of the speed
measurement system - Meas-
41
ured speed too high ................ 71
45
Table 32 Malfunction of the speed
measurement system - Meas-
49
ured speed too low.................. 71
Table 33 Swivel lifting eyes.................... 75
52
Table 34 Ring nuts to be used ............... 76
Table 35 Weights of assemblies ............ 77
53
Table 36 3 press-off screws ................... 81
61
Table 37 6 press-off screws - gas outlet
flange ...................................... 82
65
Table 38 Permissible clearances A and B 89
65
Table 39 Permitted nozzle ring com-
pression PD ............................ 90
65
Table 40 Tightening torque (51007) ....... 93
Table 41 Tightening torque (79041) ....... 95
66
Table 42 Tightening torque (72011) ....... 96
Table 43 Permissible clearances N and R
66
Table 44 Tightening torque (72020) ....... 98
66 Table 45 Tightening torque (51009) ....... 99
Table 46 Tightening torques of the
screw fittings ........................... 100
67
Table 47 Tightening torques for insulation 101
Table 48 Cover plate dimensions [mm] .. 106
67
Table 49 Customer spare part set 97070 . 111
Table 50 Spare parts list ........................ 113
68
HZTL4031_EN
Page 117 / 117
Revision D June 2016
97