Pace TJ-70 Operation & Maintenance Instructions Manual
  1. Manuals
  2. Brands
  3. Pace Manuals
  4. Power Tool
  5. TJ-70
  6. Operation & maintenance instructions manual

Pace TJ-70 Operation & Maintenance Instructions Manual

Mini thermojet handpiece
Hide thumbs Also See for TJ-70:
Table of Contents

Advertisement

Quick Links

Download this manual
TJ-70
MINI THERMOJET HANDPIECE
PACE P/N 7023-0002
OPERATION & MAINTENANCE
INSTRUCTIONS
MANUAL NUMBER 5050-0349
REV. A
For any questions regarding the following instructions, contact your local authorized
PACE dealer or contact PACE directly at:
Telephone (301) 490-9860, Fax (301) 604-9215
PACE Incorporated
9893 Brewers Court
Laurel MD 20723-1990
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TJ-70 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Pace TJ-70

Summary of Contents for Pace TJ-70

  • Page 1 OPERATION & MAINTENANCE INSTRUCTIONS MANUAL NUMBER 5050-0349 REV. A For any questions regarding the following instructions, contact your local authorized PACE dealer or contact PACE directly at: Telephone (301) 490-9860, Fax (301) 604-9215 PACE Incorporated 9893 Brewers Court Laurel MD 20723-1990...
  • Page 2 Contact your local authorized PACE Distributor or PACE Incorporated to obtain the latest specifications. The following are registered trademarks and/or servicemarks of PACE Incorporated, Laurel Maryland U.S.A. and may only be used to identify genuine PACE products or services: AdapTip, Arm-Evac, Cir-Kit, ComForm I, ConducTweez, CRAFT,...

  • Page 3: Handpiece Setup

    Its slim-line, pencil grip design and finger actuated control switch facilitates ease of use and manipulation in tight places. The TJ-70 is a member of the PACE SensaTemp family of advanced handpieces.

  • Page 4: Air Hose Connection

    NOTE Ensure that no Air Hose is connected to the SNAP-VAC Port when using the TJ-70 handpiece. The TJ-70 Air Hose must be connected to the Controllable PRESSURE Port. Attachment to both ports simultaneously will cause a deterioration of performance.

  • Page 5: Tip Installation

    TIP INSTALLATION Tip selection is very important. Referring to the list of Available Tips (Table III), select the appropriate tip for your application. The following instructions are for tip installation only. If a tip is currently installed in the handpiece, follow the “Tip Removal” procedure prior to the installation of a new tip.
  • Page 6 TIP PREPARATION TJ-70 tips are not tinnable and require little maintenance. Keep tips clean and free of any foreign particles. Insure that all tip air jets are kept clean to prevent air flow obstruction. TIP REMOVAL NOTE To avoid tip damage, the Mini ThermoJet handpiece heater must be at a temperature of at least 177°C (350°F) before attempting to remove an...

  • Page 7: Temperature Setting

    TEMPERATURE SETTING Set the operating tip temperature of the channel powering the TJ-70 handpiece to 482°C (900°F). On very light boards, you may need to lower the temperature to protect the board from damage. On MBT 250 and PRC 2000 systems, set the tip temperature offset to 3°C (6°F) (default setting).

  • Page 8: Component Installation

    NOTE To prevent damage to the component during placement, PACE recommends handling the component with a vacuum pick device such as the PACE Pik- Vac or HandiPik. Always place the hot tip in a tip holder or on a metal surface to prevent burns or scorches.

  • Page 9: Special Applications

    Controllable PRESSURE Port may be required. SPECIAL APPLICATIONS If you require assistance in the use of this handpiece or require assistance with a special application, contact PACE Applications Engineering at: Tel: (301) 490 - 9860 Fax:...

  • Page 10: Corrective Maintenance

    CORRECTIVE MAINTENANCE Your TJ-70 requires no special maintenance other than being kept clean. The heater bore and the heater assembly set screw which secures the tip must be kept free of oxidation and debris in order to maintain the proper tip to ground resistance.
  • Page 11 ONNECTOR IRING PART NUMBER DESCRIPTION HEATER ASSEMBLY 6010-0084-P1 CORD/SWITCH ASSEMBLY 6993-0134 HEATER SET SCREW 1348-0547 WIRE BRUSH, 3/16" DIAMETER 1127-0014 Handpiece tips listed following page - - - - - - - - II. TJ-70 R ABLE EPLACEMENT ARTS...
  • Page 12 SOIC Tip (dual-jet) A = 0.17" (4.32mm) 1121-0330 SOICL Tip (dual-jet) A = 0.37" (9.40mm) 1121-0331 A = 0.28" (7.11mm) 1121-0365 B = 0.074" (1.88mm) Flat End Tip A = 0.24" (6.10mm) 1121-0371 B = 0.074" (1.88mm) III. TJ-70 A ABLE VAILABLE...
  • Page 13 Largest Supplier of Electrical and Electronic Components Click to view similar products for manufacturer: pace Other Similar products are found below : 8883-0111-P5 1121-0690-P5 1124-1004-P1 1128-0003-P1 1128-0019-P1 1128-0012-P1 1128-0001-P1 1121-0416-P1 1121-0399-P1 6993- 0317-P1 6993-0210 1128-0013-P1 1121-0680-P5 1121-0003-P2 1121-0313-P1 1124-0003 6993-0316-P1 8883-0931 1131-0052-P1 1129-...

This manual is also suitable for:

7023-0002

Table of Contents