Pace TD-100 Operation And Maintenance Manual
Handpieces
Hide thumbs
Also See for TD-100:
- Installation manual (2 pages) ,
- Operation and maintenance manual (11 pages) ,
- Operation and maintenance manual (12 pages)
Related Manuals for Pace TD-100
Summary of Contents for Pace TD-100
- Page 1 Operation and Maintenance Manual for the TD-100 and MT-100 Handpieces P/N 5050-0532...
-
Page 2: Table Of Contents
PAGE Safety Guidelines ......................3 Handpiece Connection....................3 Tip Cartridge Installation ....................3 Accessory and Replacement Parts................4 Tips..........................5 Corrective Maintenance ....................10 Service ..........................10 PACE WORLDWIDE LIMITED WARRANTY STATEMENT.........11 Contact Information.......................12 ©2003 PACE Inc., Annapolis Junction, Maryland Page 2 of 12 All Rights Reserved... -
Page 3: Safety Guidelines
3. Turn the connector housing clockwise to lock in place. Tip Cartridge Installation Both TD-100 and MT-100 tip cartridges are fitted with a key lock device. This feature ensures that tip cartridges are held firmly in position and will maintain their orientation. MT-100 tip cartridges CANNOT be fully inserted into the TD-100 and TD-100 tip cartridges CANNOT be fully inserted into the MT-100. -
Page 4: Accessory And Replacement Parts
TD-100. Package of 5. TD-100 Tool Stand (TD-100 1257-0258-P1 Handpiece and tips not included) MT-100 Handpiece (Tips 6010-0140-P1 not included) MT-100 Tool Stand 6019-0069-P1 Hot Grip Removal Pad 1100-0307-P1 ©2003 PACE Inc., Annapolis Junction, Maryland Page 4 of 12 All Rights Reserved... - Page 5 Available Tips A wide variety of tip cartridges are available for use with the TD-100 and the MT-100 Handpieces. Please refer to the table below for available tip cartridge styles. PACE P/N Description 1124-0001-P1 1/32" Conical Sharp Extended 1124-0002-P1 1/64" Conical Sharp 1124-0003-P1 1/64"...
- Page 6 MiniWave 1124-0033-P1 Angled MiniWave, 3.3 mm 1124-0034-P1 Single Sided Chisel 1124-0035-P1 Angled MiniWave, 2.4mm 1124-0036-P1 1/128" Conical 1124-0037-P1 1/4 Flat Blade 1124-0038-P1 Single Sided Chisel, Fine Pitch ©2003 PACE Inc., Annapolis Junction, Maryland Page 6 of 12 All Rights Reserved...
- Page 7 MicroFine Conical, 0.25mm (.01”) 1124-0043-P1 MicroFine Bent Conical, 0.75mm (.03”) 1124-0044-P1 MicroFine Bent Conical, 0.5mm (.02”) 1124-0045-P1 Angled Micro-Wave Tip 1124-0046-P1 Micro-Wave Tip Surface Mount Removal Tips for TD-100 Soldering Iron Component Dimension A Dimension B Part Type Number Chip 402 2.2mm (.085”)
- Page 8 1124-0502-P1 Blade 21.2mm (.835”) 1124-0503-P1 Blade 25MM (.984”) 1124-0532-P1 Surface Mount Removal Tips for MT-100 MiniTweez PACE P/N Description Chip 1124-1001-P1 0.2mm (.008”) Chip 1124-1002-P1 0.5mm (.02”) ©2003 PACE Inc., Annapolis Junction, Maryland Page 8 of 12 All Rights Reserved...
- Page 9 1mm (.04”) Chip 1124-1004-P1 2mm (.08”) SOP 6 1124-1005-P1 6mm (.24”) SOP 8 1124-1006-P1 8mm (.31”) SOP 10 1124-1007-P1 10 mm (.39”) SOP 13 1124-1008-P1 13mm (.51”) ©2003 PACE Inc., Annapolis Junction, Maryland Page 9 of 12 All Rights Reserved...
-
Page 10: Corrective Maintenance
Defective Heater Change Tip Cartridge not heat Power Source Contact PACE Malfunction Table 3: Troubleshooting Service Please contact PACE or your local distributor for service and repair. ©2003 PACE Inc., Annapolis Junction, Maryland Page 10 of 12 All Rights Reserved... - Page 11 PACE Incorporated retains the right to make changes to specifications contained herein at any time, without notice. Contact your local authorized PACE Distributor or PACE Incorporated to obtain the latest specifications. The following are trademarks and/or service marks of PACE, Incorporated, MD, USA: ™...
Need help?
Do you have a question about the TD-100 and is the answer not in the manual?
Questions and answers